• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is an inconvenience. This can be an opportunity to upgrade to energy-efficient windows or insulated ones to enjoy benefits like increased comfort, higher resale value and reduced utility bills.

It's a project you can do yourself for only a fraction of the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

Replace your old single-paned windows using tempered or insulation glass to improve the efficiency of your energy, reduce noise, and protect the historic integrity of your older home. The replacement window of a window pane is relatively easy and can be accomplished by homeowners with basic hand tools. Alongside a replacement pane, the following items are required: latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty if required. Wear safety glasses and gloves prior to starting. Working with broken glass can cause serious injuries.

Begin by removing any broken pieces of glass. It is recommended to use pliers however a flathead could work as well. After that, use a wood chisel or putty knife to take the remainder of the old putty around the frame and the sash. Be careful to not scratch the window sash. Take your time and work slowly. It is a good idea to work on a stable ladder rather than the ground and have someone standing below the sash to help keep it steady.

After you have removed all the old putty, it is time to prepare the window frame for the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of width and height. These measurements can be taken to an hardware or home centers store to get an item cut from stock glass to the right size. Alternatively, you can cut the glass yourself, if you have the right tools.

After putting in the new glass, apply a small amount of caulking around the edge. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points should not be so tight that they cause friction between the frame and sash but they should not be too loose.

Before applying the putty to the surface, knead thoroughly until it is soft and free from lumps. Roll it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from one corner to the next, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of metal that allow glass to be secured into the window frame without causing any damage to the fragile surface. It's easy to learn how to use this nefarious tool, and you'll be able to save money on the expense of an installation by a professional.

After the old putty and the glazier's point are gone, thoroughly clean the frame using a utility knife to remove any remaining residue. If necessary it is necessary to lightly sand the wood along the grooves of the rabbets to smooth out rough areas. If you decide to sand wood, cover it with painter's tape to avoid accidental damage.

Take measurements of the empty frame and record precise measurements. Take these dimensions to an hardware store or home center, and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new window in the frame and press it in place with your hand. Then, use the tip of your chisel or the back end of the putty knife to make a tap on the glazier's points as shown in Figure 11. After you're done, the points should be in line with the top edge of the pane. the shoulders that are raised of the points should be below the rabbet's rim groove.

Apply a thin layer glazing compound to the rabbet grooves as well as the edges of new glass. This will seal and protect the edges. Let it dry and cure completely.

When the glazing compound is dry, you're ready to install the new window sash. The first step is to coat the wood with a thick coat of Linseed oil. This will prevent the new putty from drying out and cracking as it absorbs moisture. Apply this coat with a brush or the tip of your putty knife, then use the chisel, or the back end of the knife to gently hammer the new sash and glazier's points into the rabbet grooves. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball thrown at you or a rock that is errant or falling branch could cause a window to break or crack. The majority of Windows Glasses replacement can be repaired easily by installing a new piece. The glass is held in place with small clips made of metal called the glazier's pointed and putty, often called glazing compound. Remove the old pane and clean the area with the rag, a pull-type scraper, or a wood chisel. Wear protective glasses and gloves when you work. You'll need a heating gun in the event that the window is glued to the frame.

If you are planning to replace the original sash in the future, take care to remove the molding pieces that are used to secure the old pane. Then, sand the sash to ensure it's level and ready for new caulk. Once the sash is re-installed and sanded, apply a fresh caulk made of silicone around the glass to ensure it doesn't swell or fade over time.

Remove the glazing points in the rabbets. These are the grooves on the sash, where the glass is. If they're difficult to cut out, try holding the hand tool, such as a heat gun to soften them up first. When using a heated tool, be careful to not damage the sash and its railings.

Once the old glaze points and putty have been removed prepare a bed for the new pane. Roll a rope of glazing compound between your fingers, and make it around 1/2 inch thick. Then, push it into the rabbets where the glass will be. It is crucial that the glass sits on the putty on both sides So if you have to do so, gently tap the glass into the rabbet using your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk prior to pressing it into the sash. If not, you'll have to apply putty on the crack to form an impervious seal to keep water out. When the putty dries then clean the oily film off the glass using a rag and allow it to completely dry before painting. If you paint before the putty is completely dry, it won't form a solid seal and could leak or discolor over time.

Paint

If you've suffered a break in a window pane, you might be concerned about the expense of a new one. But the truth is that replacing a single glass pane doesn't require a huge amount of money If you can do it yourself. Even double glazed windows replacement-paned windows can be replaced at a fraction of the cost it will cost a professional.

If you are working with large glass windows, first make sure it is securely attached to the frame. With the right tools and techniques you can make this task relatively easy and quick.

If you're ready to begin taking off the old window by removing the glazing points made of metal that are connected to it. These are small metal triangles that function as "nails" to hold the window in the frame. They are placed beneath a layer of glazing putty, which hardens into a solid, moulded wedge that holds the window firmly in place and hides the window's points.

After removal of the old pane clean the frame and the wood. Scrape off any old paint, and sand the rabbet grooves where the glazing points were. These should be sanded to bare wood, so that you can paint them the same color as the rest the frame. After sanding, apply a layer of flax oil to the wood's surface to help extend its lifespan.

Then, you need to measure the width of the window opening. It is necessary to take horizontal and vertical measurements of the entire opening and also the thickness of the old pane. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal changes. You can take these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.