• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane could be a nuisance. This could be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits like increased comfort, higher resale value and lower utility costs.

You can do it yourself at only a fraction of the cost it would cost to hire an expert. It requires the right tools and only an hour or two of your time.

Glass

If your single-pane windows replacements near me are old damaged, cracked or deteriorating replacing them with more modern glass that is tempered or insulated can improve energy efficiency and reduce noise while maintaining the original character of older homes. The procedure of replacing the window pane is easy and can be completed by anyone with basic hand tools. In addition to a new pane, the following components are required such as latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty if required. Before starting, put on gloves and safety glasses as working with broken glass can cause injuries.

Begin by removing any remaining broken pieces of glass. This is best accomplished with the help of pliers but a flathead screwdriver can also be used in a pinch. Use a wood chisel, or putty knives, to take away any remaining old putty around the frame and the window sash. Take your time and work slowly making sure not to break the current window sash. It is best to work on a sturdy ladder rather than the ground, and to have someone stand below the sash to help hold it steady.

After you've removed all the old putty, it is time to prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of width and height. Take these measurements to a hardware store or home center, and find a piece glass cut to size. You can also cut the glass by yourself if you possess the appropriate tools.

After installing the new glass, apply caulking to the edge. This will make the glass weatherproof. Then install a glazier's point on the frame's opposite side to secure the pane in its place. The points shouldn't be too tight that they cause friction between the frame and sash however they should not be loose.

Before applying the putty on the surface, you must knead it thoroughly until it is soft and free of lumps. Roll it into pencil-sized strips. The first strip should be placed to the corner of the frame, working from one corner to another so that it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces of metal that help secure glass into frames for windows replacement without damaging or scratching the delicate surface. It's easy to understand how to use this nefarious tool and you can save money on the cost of an installation by a professional.

After getting rid of the old putty glazier points as well as any remaining leftovers clean the frame thoroughly using an utility knife. If needed it is necessary to lightly sand the wood along the grooves of the rabbet to smooth out rough spots. If you do sand the wood, make sure to protect it with painter's tack to avoid accidental damage.

Note down the exact dimensions of the frame. Take these dimensions to a hardware store or a home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane into the frame and push it in place by using your hands. Then use the point of your chisel or the back of the putty knife to pierce the glazier's facets, as illustrated in Figure 11. After you're done, the points should be in line with the top edge of the pane, and the shoulders that are raised of the points should be below the rabbet's rim groove.

Apply a thin layer of glazing compound on the rabbet grooves and the edges of the glass. This will protect and seal the edges. Allow it to dry completely and cure.

When the glazing compound is dry and the glazing compound is dry, you can install the new window sash. First, saturate the wood with a heavy coat of linseed oil. This will prevent the new putty from drying out and cracking when it absorbs moisture. Use a brush to apply this coat, or the tip of the blade. Then, use the chisel on the back of the putty tool or the back of the handle to gently smash the new sash or glazier's tip into the grooves of the rabbet. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown at you or an unintentional rock, or a fallen branch can cause a window to break or crack. Luckily, most windows can be repaired by simply placing a new piece in the proper place. The glass is held into position by a small metal clip, called the glazier's point, and putty. This compound is also referred to as glazing compound. Remove the old pane and clean the area with the rag, a pull-type scraper, or a wood chisel. Wear protective glasses and gloves while doing this work. You'll need a heating gun when the window is fixed to the frame.

If you're planning to install the original sash in the future, take care to remove any pieces of molding that are used to secure the old pane. Then, sand the sash to ensure it's level and ready to be re-caulked. After the sash has been put back in place then, you can apply a silicone caulk to the glass. This will ensure that it doesn't be leaking or fade over time.

Take the glazing points out of the rabbets, the grooves in the sash, where the glass is. If they're difficult to chisel, hold an instrument such as a heating gun over them to allow them to soften before. When using a heat tool, be careful to avoid damaging the sash's railings and sash.

Once the old points of glazing and putty have been removed make a bed for the new pane. Roll a piece of glazing compound between your hands, and form it into a 1/2-inch thick. Then, push it into the rabbets, where the glass will be. It's important that the glass sits on the putty on both sides So if you have to tap it, gently press the glass into the rabbet using your thumb.

If the new pane has cracked, you can apply a silicone caulk or glass glue that is based on solvents to seal the crack before pressing it in the sash. If not, you'll have to apply putty over the crack to form an airtight seal and keep water out. After the putty has dried and the film is oily, wipe it off the glass with a rag and allow it to dry completely prior to painting. Paint before the putty is completely dry. It will not create a solid seal and could discolor or leak over time.

Paint

You may be concerned about replacing a damaged piece of glass. But the truth is that replacing a single glass pane doesn't have to break the bank if you do it yourself. In fact even windows with double panes can be replaced for a fraction of the cost of a professional.

If you are working on a large window, ensure that it is securely fastened to the frame. This job can be made relatively simple and fast using the proper tools and techniques.

If you're ready to begin, begin by removing the old window by removing the glazing points of metal that are connected to it. They are basically tiny metal triangles that function as "nails" which hold the window in place in the wood frame. They are submerged beneath a bead or glazing glue that sets to form an unbreakable wedge that holds the wood frame securely in place and conceals the edges.

Once you have the old pane removed clean the surrounding frame and wood. Scrape off any paint that has been used and sand the rabbet grooves that the glazing points were. These should be sanded to bare wood so that you can paint them the same shade as the rest of the frame. After sanding, apply a coat of flax oil to the bare wood to prolong its life.

The next step is to measure the dimensions of the replacement window pane's opening. You'll need to determine the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. Take these dimensions to a hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.