• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Many terminals and PCs, however, do rely on hardware handshaking to determine when the other party (in this case the PDQ Board) is ready to accept data. By connecting pairs of these handshaking signals together, the terminal or PC can be made to think that the PDQ Board is always ready to send and receive data. Rather, it relies on software handshaking via transmission of XON/XOFF characters (ascii 0x11 and 0x13, respectively) to coordinate data transfer and ensure that information is not lost when one of the communicating parties is busy. These protocols are summarized on this page, but for more information regarding their data formats and their use for simplex or multi-drop serial lines, consult Understanding Serial Communications (but keep in mind that that page is directed to the use of the UART Wildcard, so it uses different driver functions). RS-485 is used as the physical layer underlying many standard and proprietary automation protocols used to implement industrial control systems, including the most common versions of Modbus and Profibus.

The protocols are described in turn. Because all of the serial I/O routines on the PDQ Board are revectorable, it is very easy to change the serial port in use without modifying any high level code. Resistive termination - If the PDQ Board is at the end of the RS485 cable you can terminate the cable by installing jumper caps at both jumper locations, "Term" and "RTerm". To do that, install a jumper cap at "Term" only. A jumper labeled "2 485En" (J7) enables RS485 operation on the Serial2 port if the jumper cap is installed, and configures Serial2 for RS232 operation if the jumper cap is not installed. In that case, do not install jumper caps at the jumpers labeled "Term" or "RTerm". In this case, cable connections may be made to Serial 2 on either the 10-pin PDQ Board Serial Communications Header, or the Docking Panel’s 10-pin right-angle Serial Header, or the Docking Panel’s Serial2 DB-9 Connector. The advantage of using Serial1 for RS485 is that the Serial1 RS485 signals are also available on the Docking Panel, while the Serial2 RS485 signals are available only on the PDQ Board’s Serial Communications Header. Likewise, the terminal’s transmit signal /TxD is connected to the PDQ Board’s receive signal /RxD1.

Although the RS232 protocol specifies functions for as many as 25 pins, each communications channel requires only three for simple serial interfaces: /TxD1 (transmit data), /RxD1 (receive data), and DGND (digital ground). The RS232 protocol specifies the use of two separate grounds, a signal ground and a protective (or chassis) ground. The two lowest order bits in the SPCR control register, named SPR1 and SPR0, determine the data exchange frequency expressed in bits per second; this frequency is also known as the baud rate. 1200 is the baud rate that you choose; you can specify any standard baud rate up to 4800 baud. The Serial 1 and Serial2 ports can be configured for either RS-232 or RS-485 communications at standard baud rates up to 115200 bits per second. The following table shows the connection diagram for a standard 9-pin serial cable. The pinout of the PDQ Board’s Communications Header (H2), Docking Panel’s Communications Header (H1), and the Docking Panel’s Communications DB-9 Connectors are shown in the following tables. See the following example for switching among the various parity modes on Serial1.

The Serial1 and Serial2 ports have identical communications capabilities, although more of the Serial1 signals (both RS232 and RS485) are made available on the Docking Panels headers and connectors. By default, the RS485 connections are not brought out to the Docking Panel’s DB-9 Serial1 Connector, although custom placement of zero-ohm surface-mount resistors on the Docking Panel can route the RS485 signals to the DB-9. In that case, when using very long cables you can improve noise immunity and assure a valid idle level when the transceiver is not active by installing bias resistors. Thus in the table, /RTS1 is connected to /CTS1, and /DSR1 is connected to /DTR1 and /DCD1 onboard the PDQ Board using zero ohm shorting resistors. RS485 is another protocol supported by the primary serial port on the PDQ Board. Contact Mosaic if you require RS485 signals to be routed to the DB-9 Connector. The primary and secondary serial communications ports are accessible through the PDQ Board's 10 pin, dual row Communications Header (H2) and through the Docking Panel's 10 pin, right-angle, dual row Communications Header (H1) and individual DB-9 Serial 1 and Serial 2 connectors. The mating 10-pin connectors that join the H6 header of the PDQ Board to the H4 header of the Docking Panel are typically not accessed directly, and are not discussed in detail here.