• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged or cracked window can be a source of frustration. It can also be a chance to upgrade your glass to energy efficient or insulated windows and reap benefits like more comfort, higher the value of resales and lower utility bills.

It's a task you can do yourself for a fraction of the cost of hiring a professional. You only need the proper tools and a few minutes of your time.

Glass

If your single-pane windows are outdated broken, deteriorating or damaged, replacing them with newer glass that is tempered or insulated can increase energy efficiency and reduce noise while also preserving the original character of older homes. The process of replacing a window pane is relatively easy and can be completed by anyone with basic hand tools. In addition to a new pane, the following items are required for the replacement process: latex glazing putty glazier's points; pliers; and the use of a heat gun to warm the old putty, if needed. Before beginning, wear gloves and safety glasses as working with broken glass may cause injuries.

Remove any broken glass pieces that remain. This can be done with the help of pliers but a flathead screwdriver may be used in a pinch. Then, use a wood chisel or putty knife to remove the remaining old putty around the frame and sash. Be careful not to damage the window sash. Take your time and work slowly. It is best to do this on a sturdy ladder instead of the ground and place someone on the sash to help hold it in place.

Prepare the window frame to accommodate the new pane after you have removed the old glue. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of the width and height. Take these measurements to an hardware store or home center and have a piece of stock glass cut to size. You can cut the glass yourself if you possess the appropriate tools.

After installing the new glass Apply some caulking around the edge. This will make the glass weatherproof. Then, place a glazier's tip on the frame's opposite side to secure the pane in place. The points shouldn't be too tight that they create friction between the frame and the sash However, they should not be loose.

Before putting the putty on, knead it thoroughly until it is soft and free of lumps. Then, roll it into pencil-size strips. Place the first strip to the corner of the frame, moving from one corner to the next to ensure it is even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces that help secure glass into frames for windows without scratching or damaging the delicate surface. Understanding how to use these hidden tiny helpers is simple and could save you money on professional installation or the cost of purchasing new glass.

After the old putty and the glazier's points have been removed Clean the frame thoroughly with a utility knife to get rid of any remaining traces. If necessary you can lightly sand the wood in the grooves of the rabbet to smooth out rough spots. If you decide to sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Note down the exact dimensions of the frame. Take these dimensions to a hardware store or home center and request that the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane in the frame and push it in using your hands. Then, you can use the point of your chisel or back of the putty knife to tap in the glazier's points, as illustrated in Figure 11. The glazier's point should be aligned with the top edge of your pane, and the shoulders should be just beneath that lip.

Apply a thin bead of glazing compound over the edges of the new glass and in the rabbet grooves to seal and Replace window pane protect them. Allow it to dry and cure completely.

Once the glazing compound has dried, you're ready to install the new window sash. The first step is to coat the wood with a thick coat of linseed oil. This will stop the new putty from drying out and cracking as it absorbs moisture. Apply this coat using a brush or the tip of your knife, and then use the chisel or the back end of the knife to gently press the new sash and glazier's point into the rabbet grooves. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A hurled baseball, an errant rock or a falling branch can cause a window to break or crack. Fortunately, the majority of windows can be replaced by simply placing a new piece in place. The glass is held in the position with a tiny metal clip, called the glazier's point, and putty. This compound is also called glazing compound. Remove the old pane and clean the area using the rag, a scraper that is a pull type or a wood chisel. Wear gloves and safety glasses while working. You'll need a heating gun in the event that the window is glued into the frame.

If you're planning to install the original sash in the future, take care to remove any pieces of molding that hold the old pane in place. Then sand the sash to ensure it's smooth and ready for new caulk. After the sash has been installed, you can apply a silicone caulk on the glass. This will ensure that it won't be leaking or fade over time.

Remove the glazing points in the rabbets. These are the grooves in the sash where the glass is. If they're difficult to cut out, you can try holding an instrument like a heat gun to soften them first. When using a heated tool, be sure to avoid damaging the sash's railings and sash.

After the old glaze points and putty have been removed, replace window Pane make a bed for the new pane. Roll a piece of glazing compound between your hands, and form it into a 1/2-inch thick. Then, press it into the rabbets, where the glass will be. It is essential that the glass sits on the putty on each side So if you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane is cracked, you can use a silicone caulk or glass glue based on solvents to cover the crack before pressing it into the sash. If not, you'll have to putty over the crack to create an airtight seal and keep water out. After the putty has dried remove the oily film off of the glass and let it dry completely before painting. Paint after the putty has completely dried. It won't make a strong seal and may discolor or leak over time.

Paint

If you've suffered a break in a window pane, then you may be concerned about the expense of a new one. However, replacing a single glass pane doesn't need to cost a fortune If you can do it yourself. Even a double glazing replacement window-paned window could be replaced for a fraction of what it will cost a professional.

If you're working with a large glass window, first make sure it is securely fixed to the frame. This can be made relatively simple and fast using the right tools and techniques.

Once you're ready to begin, begin by removing the old window pane by prying out the glazing points made of metal that are connected to it. These are essentially small metal triangles that function as "nails" that hold the window in within the frame of wood. They are submerged beneath a layer of glazing putty, which is then cured to form a solid, formed wedge which holds the window in place and conceals the window's points.

After removing the old pane, clean the frame and the wood. Scrape away any paint and sand down the rabbet grooves, where the glazing points were. They should be sanded to the point of being bare, to allow you to paint them the same shade as the rest of the frame. After sanding, apply a layer of flax oil on the bare wood to extend the life of the frame.

Then, you need to measure the width of the window's opening. You will need to take horizontal and vertical measurements of the entire opening and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. You can take these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.