• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Double Glazing Door Lock Repairs

Has your uPVC window or double glazing repair door mechanism deteriorated? Perhaps the handles on your uPVC windows or doors aren't aligned properly or are difficult to operate.

It is essential that the double glazed doors function smoothly, or else you'll be wasting energy and increase the chances of burglary. Owen the Locksmith can fix your door lock at an affordable cost.

Snapped Key

If a key breaks within a lock, it can be extremely frustrating. It could also be an issue for security, since the door may not lock and leave you open to intrusion. There are a few easy solutions you can use to fix the problem and get your door working again.

Be sure to remain calm. If you panic and start doing a lot of fumbling around, you might just end up pushing the damaged piece of the key deeper into the lock, thereby making the situation even more difficult.

Spray WD-40 or another penetrating oil, into the lock. This will assist the broken piece be removed more easily. You can also use the screwdriver to break up any pieces that are stuck. If you're fortunate enough to have a little bit of the key that is visible and you want to remove it, make use of a paperclip, or any other thin metal object to grab it and pull it out. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges that can work in a pinch as hook extractors and Jigsaw blades also work for this function. If you don't happen to have one of these tools, you can bend a hook using needle-nosed pliers. You can also use a pair tweezers to grab and pull out the last bit of the broken keys.

If you can't get the broken piece of key out, try using a lock de-icer. This is usually available at most hardware stores. It works by freezing any moisture or ice that might be inside the lock.

If none of these methods seem to be helping you, it's time to call in locksmith. Fitlocks experts can fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are simpler to operate. Book a double glazing repair via our website, or give us a call to discuss your needs.

Broken Cylinder

A damaged cylinder can pose a serious security threat. It's fortunately a simple repair for a professional locksmith to complete. To repair the cylinder, a locksmith will need to tap it. They can do this using a hammer or other tool, but the best way is to use a long match or a piece of wire. Place the match or wire's end close to the keyway. The locksmith will then strike the lock in order to break it. This is more secure than using the hammer, which could cause damage to the lock.

Overheating is the main cause of cylinder heads cracking. This can occur when the cylinder block and cylinder head are made of various metals, such as cast iron and aluminium. Different metals will heat up and cool down at different rates. This can cause localised hotspots to expand faster than the rest of the cylinder.

Corrosion is a different cause of cylinder fractures. If the head and block of a cylinder are not maintained in a timely manner they may be corroded or rust and cause them to expand faster than expected. Over time, this can also cause cracks.

If your uPVC window lock or door is stiff or requires a lot of pressure to turn, it could be due to a number of things. A defective locking mechanism, misalignment or an old handle are the most common causes of this issue.

Fortunately, this is an easy and inexpensive fix for most homeowners with double glazing. A professional locksmith will usually solve this issue within an hour of arriving at the property. They can replace the locking mechanisms, or change the window handles and replace the gearboxes, based on your particular requirements. A locksmith with experience can always advise you on the most cost-effective options for your home. They can recommend upgrading to 3 Star TS007 Euro Cylinders, which provide an additional security layer from burglars. It's a small price to pay for the security that comes with knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks can break. They have complex mechanisms that become less effective over time. It isn't always easy to pinpoint the cause of the problem and then fix it properly.

Whether the problem is in the internal locking mechanism or the latch, fixing the broken handle will increase your uPVC double glazing door's security and allow you stop draughts. Incorrectly repairing or replacing your handle can be very expensive and could damage the door's frame and lock and frame, so it's worth spending the time to do it right.

With the window in the open position and the window open, loosen the screw that holds the handle with the screwdriver. The screw should be located on the inside of the backplate, which is usually covered by a screw cap to enhance the appearance. You should not lose any internal parts of the handle such as the levers and plates on either side. Keep them in the same arrangement so that it is easier to replace them if needed.

Then, using another screwdriver take the screw off that connects the handle to the spindle on the back. Once the screw is free, you can pull the handle out and take out the broken spindle. Replace it with a brand new spindle, making sure it's the same length (you can find them online or at hardware stores). Screw it into place. Do not tighten the screw too much because this could harm the handle as well as the window frame.

Close the handle and try it. It is likely that it will operate smoothly and you'll be able to open your window once more.

Be sure to double-check that your upvc repair window is shut properly while you're working with the handle. If they're not closing properly, you could experience draughts or damp in your home. Also, you could be compromising the energy efficiency of your home. A local window company, such as Core Sash Windows, double glazing repair will be able to adjust the hinges on your window frames to ensure they can shut properly.

Broken Spindle

It is more likely for the spindle to break rather than the handle. This is most common in uPVC tilt-and-turn windows. These windows require a handle that operates a locking mechanism in the window frame. The handle is connected to a central rod that activates a series of mushroom-shaped locking cams that lock into the window frame keep. If the dead latch mechanism is not able to open when the handle is turned, it is possible that the spindle has broken, this can be a very frustrating issue.

There are solutions to this problem. A good locksmith will be able to quickly and effectively fix this issue. A professional locksmith can disassemble the handle of the window by using a tool to remove the wheel from the area where the spindle is located. This can be done with no damage to the handle or window frame.

After removing the wheel the technician can inspect the spindle and determine the cause of the break. This involves breaking down the spindle into its component components and carefully observing their general condition as in addition to any specific areas of wear or damage. This procedure is typically carried out by technicians in a clean and safe environment.

Then, clean the damaged spindle. This will help remove any dirt or debris which might be preventing it from working normally. Following this the spindle is cleaned, it could be repaired or replaced. If it is being replaced the technician could use the dowel that is similar in size to the original and drill mating holes into both pieces of the spindle. This will ensure that the new spindle is precisely matched to the handle.

If the damaged spindle is beyond repair, it may be necessary to replace it completely. Home centres sell generic replacements but if the style of your window is rare then it will be necessary to speak with a woodworker or cabinet maker who can make the exact part for you. After the spindle is installed, it is attached to the handle. The screw holes on the handle with the existing screws in the frame. Once the handle is firmly in place, you can use your uPVC windows.