• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat 500 Key Fob Won't Work

A fiat 500 key fob is a convenient method to open the doors and start the car. There are many reasons why the fob won't work. These include a dead battery, water damage, receiver module issues, or interference.

This listing is for an NEW replacement fiat key fob Fiat 500 Electric Key Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is the battery is dead. Modern key fobs only have a limited range of operation and must be within only a few inches from the vehicle in order to function. If you are far from your vehicle, and you press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. You can find them at your local hardware store, or online.

You can test the battery in the coin-cell by pressing the buttons while standing close to your fiat panda remote key replacement 500. The parking lights should blink and the key fob should operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it may have water damage that prevents it from connecting to the receiver module in your vehicle. Water damage can happen through a variety of methods, including the simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture back out. If this doesn't work your fob is likely to need to be reset by an experienced auto locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short, and fiat 500 Electric key eventually die. It's not good to get the fob wet however, but don't give it up even if you accidentally drop the fob in water or fail to remove it from your pants pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl, or a similar product. Next check the fob to see if it works. If the key doesn't function, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is a bit older and fiat 500 Electric key has not been programmed to work with your vehicle it is necessary to replace it completely. This is a simple procedure that can be completed by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition on your vehicle. They will also need to reprogram the fob to the system of your car. This is a fast and inexpensive process that can usually be completed the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob could stop functioning is because it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced the battery in your coin (commonly called"button" or "button" or "watch") and your fob doesn't function it could be due to an internal circuit board issue. In the majority of cases, reprogramming your fob will solve the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that hold the coin batteries in place. If they loose tension, it could hinder the coin battery from being seated properly and can result in the malfunction of your remote.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances, they may need to reinstall the software on your body control module, as well.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This is possible when the key fob is located near radio transmitters (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob might not work include a weak connection to the buttons or damage to the internal chip or water damage.

If the key fob suddenly stopped working, out of the blue or after trying every option at home to fix it e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy way to reset every single system on board in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which can help you get your key fob working again. If the issue continues you should speak with an expert technician. They can diagnose the exact cause of your issues.