• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged or cracked replacement window glass near me is an inconvenience. It could also be an opportunity to upgrade your glass to energy-efficient or insulated windows and benefit from improved comfort, increased the value of resales and lower utility bills.

It's a task you can take on yourself for only a fraction of the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

Replace your old single-paned windows using tempered or insulated glass to increase energy efficiency, cut down on noise, and maintain the original character of your older home. The majority of homeowners with basic hand tools can repair a window pane. You will also require an additional window pane, glazier's suggestions, replace Window pane pliers, and latex glaze putty. If necessary you can use a heatgun to warm the old putty. Before starting, wear gloves and safety glasses as working with broken glass could cause injuries.

Remove any broken glass pieces that remain. It is best to use pliers however a flathead could be used as well. Then, use a wood chisel or putty knife remove the remaining old putty from around the frame and the sash. Work slowly and carefully and be careful not to damage the old window sash. This can be done best on a ladder, not on the ground. Also, ensure that someone below the sash keep it in place.

Make sure that the window frame is ready to receive the new pane when you have removed the old glue. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of the width and height. Bring these measurements to the nearest hardware store or home center and have a piece of stock glass cut to size. You can also cut the glass yourself if you have the appropriate tools.

After installing the new pane after installing the new pane, put a tiny amount of caulking around the edge to make it weatherproof. Then, place a glazier's tip on each side of the frame to secure the pane in its place. The points should not be tight enough to create friction between the frame and sash, but they should also not be loose.

Before applying the putty to the surface, gently knead it until it is soft and free from lumps. Roll it into pencil-sized strips. The first strip should be placed in the corner of the frame, working from one corner to the other so that it is even and smooth.

Glazier's Points

The glazier’s points are small triangular metal pieces that help secure the glass into the window frame without causing damage to the delicate surface. Knowing how to use these hidden tiny pieces of help is simple and could save you money on a professional installation or the cost of purchasing new glass.

After getting rid of the old putty glazier points as well as any remaining remnants, clean the frame thoroughly using a utility knife. Lightly sand the wood into the rabbet grooves if needed to smooth out rough areas. If you sand wood, protect it with painter's tape to avoid accidental damage.

Note down the exact dimensions of the frame. Take these dimensions to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane into the frame and press it into place firmly using your hand. Use the chisel's point, or the back of the putty knife to tap the glaziers' points as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane, and the shoulders of the points should be just below the lip of the rabbet groove.

Apply a thin layer glazing compound on the rabbet grooves as well as the edges of new glass. This will protect and seal the edges. Allow it to dry and cure completely.

After the glazing compound dries it's time to put in the new window sash. First, you need to coat the wood with a thick layer of linseed. This will stop the new putty from drying out and cracking due to the moisture it absorbs. Apply the coating using a brush this coat, or even the tip of the putty blade. Then, use the chisel on the back of the putty tool or the back of the handle to gently hammer the new sash or glazier's point into grooves of the rabbet. Repeat this procedure every 10 inches around the perimeter of the frame.

Putty

A baseball thrown or a rock thrown by error, or a tree falling can cause a broken or cracked window pane. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in place with small clips made of metal called the glazier's pointed and putty, often called glazing compound. Before you install a new pane, first take out the old one and clean up the area with a rag and the pull-type paint scraper or a wood chisel. Wear protective glasses and gloves while you do this work. You'll require a heat gun when the window is fixed to the frame.

If you're planning to install the original sash, gently remove any molding pieces that secure the old pane. Sand the sash until it is flat and ready for new caulk. Once the sash is re-installed, apply a new silicone caulk around the glass to ensure that it doesn't swell or fade in time.

Remove the glazing points from the rabbets, or the grooves in the sash, where the glass sits. If they're hard to cut, place a hand tool such as a heating gun over them for a few minutes to soften them. When using a heated tool, make sure to not damage the sash's railings and sash.

Make a bed for your new pane after you have removed the old glaze points and putty. Roll a rope of glazing compound between your hands, forming it to be around 1/2-inch thick. Place it into the rabbets, where the glass will be put. It's important that the glass sits on the putty on both sides So if you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has a crack, you can cover it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If the crack isn't sealed, you will need to apply putty to keep water from getting in. Once the putty is dry remove the oily film off the glass and allow it to dry completely before painting. If you paint before the putty is completely dry, it will not form a solid seal and could discolor or leak in time.

Paint

You might be worried about replacing a broken pane of glass. In reality, replacing a single pane glass doesn't have to be expensive even if you do it your own. In fact windows with double panes can be replaced for a fraction of the cost of an expert.

If you are working on a large window, ensure that it is securely fixed to the frame. This task can be done relatively easy and fast using the right tools and techniques.

When you are ready to start, remove the old window pane. Take out the metal glazing points attached to it. These are tiny metal triangles which act as "nails" that hold the window in the frame. They are buried beneath a bead or glazing glue that hardens to an unbreakable wedge that holds the frame securely in place and hides the sharp edges.

After removal of the old pane clean the frame and the wood. Scrape away any paint and sand down the rabbet grooves, where the glazing points were. These should be sanded to bare wood so that you can paint them the same shade as the rest of the frame. After sanding the wood, apply a layer of flax oil. This will help prolong the life of the frame.

The next step is to measure the dimensions of the window's opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. To determine the exact size of the new pane subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these measurements to the hardware or home improvement store and ask them to cut you a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.