• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window pane Window Panes

A damaged window pane could be a nuisance. It could be a chance to upgrade to energy-efficient windows or insulated ones to enjoy benefits like increased comfort, higher resale value and reduced utility costs.

You can do it yourself at only a fraction of the cost it would cost to hire an expert. It requires the right equipment and an hour or two of your time.

Glass

If your single pane windows are old broken, deteriorating or damaged replacing them with modern glass that is tempered or insulated will increase energy efficiency and decrease noise while maintaining the original character of older homes. The replacement glass for windows of the window pane is easy and can be accomplished by homeowners with basic hand tools. Alongside a replacement pane, the following components are needed: latex glazing putty; Glazier's points; pliers and a heat gun for warming the old putty if required. Before beginning, wear protective gloves and goggles since working with broken glass could cause injuries.

Remove any broken glass pieces that remain. It is best to use pliers however a flathead could work equally. Utilize a wood chisel or putty knives, to take away any old putty that remains around the frame and the window sash. Take your time and work slowly making sure not to break the existing window sash. It is recommended to work using a sturdy ladder rather than the ground, and to place someone on the sash in order to help hold it in place.

Make sure the window frame is ready to accept the new pane once you have removed the old putty. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. These measurements can be taken to a hardware or home center store to get an item cut from stock glass to the right size. You can also cut the glass by yourself if you possess the right tools.

After putting the new pane in place after installing the new pane, put a tiny amount of caulking around the edges to make it weatherproof. Then install a glazier's point on each side of the frame to hold the pane in place. The points shouldn't be tight enough to create friction between the frame and [Redirect-302] sash however they should not be loose.

Before applying the putty to the surface, knead thoroughly until it becomes soft and free of lumps. Then make it into pencil-sized strips. Apply the first strip to the frame's corner. Work from one corner to the next, making sure it is even and smooth.

Glazier's Points

The glazier’s points are small triangular metal pieces which help to secure the glass to the frame without damaging the delicate surface. Understanding how to use these tiny pieces of help is simple and could save you money on a professional installation or the cost of buying new glass.

After the old putty as well as glazier's points are removed Clean the frame thoroughly using a utility knife to eliminate any remaining traces. Lightly sand the wood in the rabbet grooves if needed to smooth rough areas. If you do sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Write down the exact dimensions of the frame. Bring these measurements to a hardware store or a home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit, and allow for expansion and contraction.

Place the new window in the frame and push it in place by using your hands. Then, you can use the point of your chisel or back of the putty knife to pierce the glazier's points as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane and the shoulders that are raised of the points should be below the lip of the rabbet groove.

Apply a thin layer of glazing compound over the edges of the glass that has been made and into the rabbet grooves, to seal and protect them. Allow this to dry and cure fully.

Install the new window sash once the glazing compound has dried. The first step is to coat the wood with a thick layer of linseed. This will stop the new putty from sucking up moisture and deteriorating and cracking with time. Apply the coating using a brush this coat, or even the tip of the putty blade. Then, use the chisel that is on the back of the putty tool or the back of the putty handle to gently hammer the new sash or glazier's point into the rabbet grooves. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown at you or a rock that is errant or falling branch could cause a window to break or crack. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in position by a small metal clip, called a glazier’s point and putty. This compound is also referred to as glazing compound. Remove the old pane and clean the area using the rag, a scraper that is a pull type or a wood chisel. Wear safety glasses and gloves while working. You'll need a heating gun if the window is glued to the frame.

If you're planning to install the original sash, remove any pieces of molding that secure the old pane. Then you can sand the sash down to ensure it's smooth and ready for a new caulk. Once the sash is reinstalled, you can apply a silicone caulk over the glass. This will ensure that it won't get soiled or discolor over time.

Remove the glazing points from the rabbets. These are the grooves on the sash where the glass is. If they're difficult to cut out, try placing a hand tool like a heat gun over them to soften them first. If you're using a heat gun, be cautious not to damage the railings or sash by holding the tool too tightly.

After the old points of glazing and putty have been removed, prepare a bed for the new pane. Roll a rope made of glazing compound between your fingers, and make it around 1/2 inch thick. Place it into the rabbets where the glass will be placed. The glass should rest against the putty on both sides. If needed, lightly tap your glass into the rabbet using your thumb.

If the new pane has a crack you can fill it with a solvent-based glass glue or Envtox.snu.ac.kr/bbs/board.php?bo_table=sub5_4&wr_id=637623 silicone caulk prior to pressing it into the sash. If the crack isn't sealed, you'll need to use putty to keep the water out. After the putty has dried, clean the oily film off the glass using the help of a rag. Allow it to dry completely prior to painting. Paint before the putty is completely dry. It won't create a solid seal and may leak or discolor with time.

Paint

If you've suffered a break in a window pane, then you may be concerned about the expense of replacing it. In reality, replacing a single pane glass doesn't have to be costly if you do it on your own. Even a double-paned window can be replaced at a fraction of the cost it will cost an expert.

First, if you are working on a large window, make sure it is securely fastened to the frame. With the right tools and techniques you can complete this task easily and quick.

When you're ready to start with the removal of the old window pane by prying out the metal glazing points that are connected to it. These are basically small metal triangles that act as "nails" that hold the window in within the frame of wood. They are submerged beneath a bead or glazing putty that sets to form a solid wedge that holds the frame firmly in position and conceals the edges.

After taking off the old pane clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. Sand them down to bare wood surfaces, so that you can paint the frames with the same shade. After sanding, apply a layer of flax oil on the wood's surface to extend the life of the frame.

Next, measure the width of the window's opening. You will need to take horizontal and vertical measurements of the entire opening and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you get a precise size for the new pane. This will also allow for expansion and contraction of the glass during seasonal change. You can bring these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.