• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high above the ground, moving huge panes of glass. They follow strict safety protocols and often work under extreme weather conditions.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty using an utility knife. A heat gun can soften the old putty and make it easier to remove.

Replacement

It is tempting to fix the glass of your window instead of replacing it when a pane breaks. However, replacing a window is typically more cost-effective and can assist in preventing other issues in your home's energy efficiency. Examine the kind of glass damaged to determine if it's a temporary fix, or if a more permanent solution is needed.

The first step in fixing damaged windows is to remove the sash, or frame and installers place it flat on a table. Wearing eye protection, carefully wiggle and pull out any shards that remain within the window. Then, use a utility knife to cut off the glazing compound and glazing points that keep the glass in the position. Keep an eye on the location of these components to make sure they can be put back in place later.

After removing the frame and sash, you can start preparing to replace the glass. Make sure you check the opening of the frame is the right size for your replacement window. Measure both ways across the opening, then subtract 1/8 inch from each measurement in order to leave space for expansion and contraction of the frame and glass. Then, purchase double-strength glass that are cut to these exact dimensions. It is also recommended to purchase enough new glazier's points or clips to be installed every 6 inches around the window pane.

If the manufacturer is accountable then you should call them and file a claim. After the new glass has been installed it is crucial to cover it with a thin layer of glaziers compound. Once the compound has dried it is possible to paint the frame to be a perfect match.

If the crack is greater than an inch you can stop it from expanding by cutting a small arc just beyond the crack. This trick won't be foolproof, but it can slow the development of the crack down to a manageable size until you are able to take more permanent measures.

Repair

Professional window installers know how to deal with a variety of glass and have the tools needed to complete an excellent job. They are able to dispose of waste in a safe manner and are therefore less likely than other people to leave behind pieces of glass which could cause harm to family members or pets. They're also familiar with various types of windows, and they may be capable of identifying issues that might not be apparent to the uninitiated homeowner.

Wear safety glasses and gloves prior to starting the process of repairing cracked glass. Even a small crack can cause shards of glass to fly and put anyone at risk within or around the home. It is important to determine the cause of the crack, so that you will help prevent any future issues.

Begin by creating an epoxy mixture that has two parts. They are typically 50/50 mix of resin and hardener, and must be mixed quickly. After the mixture is made then apply it directly to the crack and allow it to dry. It should take only some minutes however it is important to work quickly since the mixture is very thick and fast-drying.

Once the epoxy has dried, you can take off excess epoxy with a blade. Then, you'll need to clean the area around the crack of glass. If you do not clean the area correctly the residue could cause further damage to your glass. After the glass has been cleaned using a putty knife, you can use it to smooth the compound along the edge of the window and to match it to the frame made of wood.

Think about using a plastic lid for a more durable option. A trash bag that is heavy-duty or tarp is ideal, however you can also apply masking tape to the glass. This will stop the crack from spreading and will also keep water, wind and bugs out.

You can create an interim fix in the event that you are unable to reach the window glass repairs in an efficient manner. Simply place a tiny amount of the stuff around the outside edge of the broken window. It won't fully seal the gap between frame and glass, but it will keep the crack in place while you repair it.

Repainting

Repainting your old glass windows is a good idea. This is a low-cost alternative to replacing windows, and it can give your home a fresh new appearance. Before painting, installers make sure the surface is clean. Use soap or rubbing alcohol and water to remove oil smudges, as well as other residues that could prevent paint from adhering. It is also recommended to wear rubber gloves when working on glass to avoid the risk of transferring your own oils onto the surface of the window. Apply several thin coats instead of a single thick one. This will make the paint last longer, and keep your windows looking even and smooth.

Make sure you have the right tools on hand if you plan to repaint glass windows. You'll need a brush, sponge, painter's tape a ruler, toothpicks, and other tools such as a rag or paper towel. You'll need the paints and brushes that you will be using in your kit. Be sure to follow the manufacturer's instructions and have a good amount of patience as it can take awhile for the paint to dry.

It is also important to ensure that the room you're working in is ventilated when you're using solvent-based paint. This will decrease the chance of inhaling toxic chemicals, and the paint will dry faster. Also, make sure you have a mask to protect yourself for any spray paints you use.

For older glass windows, it is necessary to prepare the surface before painting. Use soap and warm water to thoroughly clean the glass upvc window repair. Then, use rubbing alcohol on any grease or oil residues that might hinder the adhesion of the paint. Make sure the windows are completely dry before you begin to paint them.

If your glass windows are energy efficient dual pane windows, then you might be eligible to submit a claim to the window manufacturer or dealer who sold them to cover any repair or replacement costs. This is particularly the case if you've experienced numerous issues with condensation or broken glass while the windows are still covered by warranty.

Sealing

Whether you have old double-pane windows with a damaged seal or more recent insulated glass units (IGUs) that have experienced defogging or fog, there are many options to address the issue. The most expensive option is to replace the insulated unit and frame but it may be required if fog or condensation is causing energy loss. Other options include replacing the IGU with a single-pane, or fixing it by drilling a small hole into the bottom of the unit, and then filling the solution with anti-fog.

You can also seal the gap between the window frame and the threshold or sill by using a felt strip, vinyl v-strips, or door sweep. Felt can be stapled, glued, or nailed into place but doesn't offer much protection against moisture. Vinyl weather stripping v-strip is durable and easy to install however it can be costly and is usually reserved for areas that are exposed to abrasions that are high. Door sweeps are easy to nail in place and are cheap. However, they provide only a small amount of protection between the threshold and the air.

To fix a cracked window seal, first employ a putty knife to take off the old caulk. Wearing gloves and eye protection remove the glazing point -- tiny fasteners with sharp pointed tips that secure the glass to the frame's recess. Once you have removed the glazing points, clean the grooves and sand the wood smooth. Wipe off any sanding debris then seal the wood surface using a linseed oil-based paint or clear sealer.

A putty or caulking knife can be used to apply traditional glazing putty. However, a knife will provide a more precise application, and a stronger seal. Select a putty made specifically for glass windows, as it will have higher adhesion and long-lasting.

Apply a thin bead of the putty to the inner edge of the frame where it meets the glass. Slide the window into the frame, so that the scribed line on the glass lines up with the frame's edge. Apply pressure to the glass to press the putty and create an elongated seal. Smooth the compound with gloves and then remove any drips or caulk that were applied incorrectly before it dries.