• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a source of frustration. It can also be an opportunity to upgrade your glass to energy efficient or insulated windows to benefit from more comfort, higher potential for resales, and less bills.

It's a task you can tackle yourself at only a fraction of the cost of hiring an expert. You'll need only the right tools and a few minutes of your time.

Glass

If your single-pane windows are old broken, deteriorating or damaged, replacing them with newer glass that is tempered or insulated can increase energy efficiency and decrease noise while also preserving the original character of older homes. Most homeowners with basic hand tools can repair the window pane. You will also require an additional window pane, glazier's tips pliers, and latex glaze putty. If needed you may make use of a heat gun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass could result in serious injuries.

Begin by removing any remaining broken pieces of glass. This is best accomplished with pliers, however, a flathead screwdriver can also work in a pinch. Then, use a wooden chisel, or putty knife, to remove the rest of the old putty from around the frame and sash. Be careful not to scratch the window sash. Work slowly and carefully. This is best done on a ladder, not the ground. Also, ensure that someone below the sash keep it in place.

After you've removed all the old putty, prepare the upvc replacement window handles frame to fit the new pane. Measure the width and height of the opening for the sash and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to a hardware store or home center and get a piece of stock glass cut to size. Alternately, you can cut the glass yourself, if you have the appropriate tools.

After installing the glass, apply a small amount of caulking around the edge. This will make the glass weatherproof. Install a glazier's pointing on both sides of the frame. This will help secure the pane. The points should not be so tight that they cause friction between the sash and the frame, but they also should not be too loose.

Before applying the putty on the surface, you must knead it thoroughly until it is soft and free from lumps. Make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to another, making sure it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal which help to secure the glass into the window frame without causing any damage to the fragile surface. Learning how to use these hidden little helpers is easy and could save you money on a professional installation or the cost of buying new glass.

Once the old putty and the glazier's point are gone Clean the frame thoroughly with a utility knife to remove any remaining residue. Lightly sand the wood into the rabbet grooves, if necessary, to smooth rough areas. If you decide to sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Write down the exact dimensions of the frame. These measurements can be brought to an hardware or home centers store, and the new pane will be cut a bit smaller. This will ensure a secure fit and leave room for expansion and contraction.

Place the new window in the frame and press it into the frame with your hand. Then use the point of your chisel or the back end of the putty knife to tap in the glazier's facets, as shown in Figure 11. When you're done, they should be flush with the top edge of the pane and the shoulders that are raised of the points should be just below the rabbet's lip. groove.

Apply a thin layer of glazing compound on the rabbet grooves as well as the edges of new Glass Window Replacement. This will seal and protect the edges. Allow it to dry and cure completely.

Install the new window sash after the glazing compound has dried. First, you need to coat the wood with a thick layer of linseed. This will prevent the new putty drying out or cracking due to the moisture it absorbs. Apply this coat with a brush or the edge of your putty knife, and then use the chisel or the back end from the putty knife to gently hammer in the new sash and glazier's points into the grooves of the rabbet. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A baseball hit, a rock thrown in error, or a fallen tree can result in a cracked or cracked window pane. Fortunately, the majority of windows can be replaced by simply putting a new piece of glass in its the proper place. The glass is held in position by a small metal clip, also known as the glazier's point, and putty. This compound is also known as glazing compound. Remove the old pane and clean the area using a rag, a pull-type scraper or wood chisel. Wear gloves and safety glasses while you do this work. You'll need a heating gun in the event that the window is glued to the frame.

If you're planning to replace your original sash, remove the molding that holds the old pane. Sand the sash until it's flat and ready for new caulk. Once the sash is installed and sanded, apply a fresh silicone caulk around the glass to ensure that it doesn't swell or fade over time.

Take out the glazing points in the rabbets. These are the grooves in the sash, where the glass is. If they're difficult to work out, you can try holding a hand tool like a heat gun over them to soften them before you do. When using a heating tool, be careful to avoid damaging the sash's railings and sash.

Once the old glazing points and putty have been removed make a bed for the new pane. Roll a piece of glazing compound between your hands, forming it to be about 1/2-inch thick. Press it into the rabbets where the glass will be placed. It is essential that the glass sits on the putty in all places on both sides If you have to tap it, gently press the glass into the rabbet with your thumb.

If the new pane has cracked, you can use a silicone caulk or glass Window replacement glass glue based on solvents to cover the crack before pressing it in the sash. If the crack is not sealed, you'll need to use putty to keep water from getting in. After the putty is dry, clean the oily film off the glass using the help of a rag. Allow it to dry completely before painting. If you paint before the putty has completely dry, it will not form a strong seal and may discolor or leak in time.

Paint

If you've had a broken window pane, you might be worried about the expense of replacing it. But the truth is that replacing a single glass pane doesn't have to break the bank If you can do it yourself. In fact, even a double-pane window can be replaced for only a fraction of the cost of a professional.

If you are working on a large-sized window, ensure that it is securely fixed to the frame. By using the correct tools and techniques, you can accomplish this task fairly easily and quick.

When you are ready to begin taking down the old replacement window seals pane. Pry out the glazing points made of metal that are attached to it. They are basically tiny metal triangles that function as "nails" which hold the window in place in the wood frame. They are submerged beneath a bead or glazing putty which hardens into a solid wedge which holds the wood frame securely in place and conceals the edges.

After removal of the old pane clean the frame and wood. Scrape away any old paint and sand down the rabbet grooves, where the glazing points were. They should be sanded to the point of being bare, glass window replacement to allow you to paint them the same color as the rest the frame. After sanding, apply a layer of flax oil on the wood that is not sanded down to help extend its lifespan.

The next step is to measure the dimensions of the window opening. You will need to take vertical and horizontal measurements of the entire opening and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will allow for seasonal changes in the glass. Take these dimensions to your local hardware or home improvement store, and they will have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.