• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

And since a 120 Ω termination resistor can cause enough signal loss with an extremely long 120 Ω cable to stop the network from functioning, a 500 Ω or even a 1kΩ termination resistor may improve the signal quality enough without causing too much signal loss for the network to function. If CAT-5 (100 Ω cable) cable is used, the termination resistors should be 100 Ω. POTS telephone cable varies from 600 Ω at audio frequencies (say 1kHz) to 100 Ω at 1MHz, while CAT-5 cable is around 100 Ω over a wider frequency range. While it may seem quite rational to assume that an RS-485 driver IC pin that is labeled A matches the RS-485 standard's wire "A", this is actually an assumption and is in fact not the case. If the data bit is sampled while there is ringing it may be sampled as an incorrect value. If the serial port terminal device receives data but does not respond properly, monitor the data from the serial port device.

RS232 is without doubt the best known interface, because this serial interface is implemented on almost all computers available today. It is faster and much more versatile than the older RS232. Unit Load measures how much load a device can impose on the communication link. How much of each depends on the wires and the insulation. A signal traveling down the wires will reach the end and "reflect" off of it (at the receiver's end). Increasing the frequency will increase the inductive reactance, thereby increasing the series resistance in this model. Again the amount of loss depends of the values of the series and parallel resistance and the loss will increase with frequency. Only end devices will have a single pair of wires terminated into the communication connector, except for necessary End of Line (EOL) terminators or bias circuits. This scheme will automatically take control of the network when a byte is transmitted, but there will not be any guaranteed marking time so bias resistors may be required. Any receiver connected at some point in the cable will change the impedance of the cable at that point on the cable.

The "pin mislabeling" discussed above is a good starting point. Some manufacturers have avoided this confusion by changing the name of the output pins labels to X and Y. There are two things to be noted about this so called "pin mislabeling". There are a number of other things to note with this model. Well if you paid attention to the previous discussion, there is no way. 12: Using the absolute encoder should pay attention to what matters? You can design the system to accomplish this if you pay careful attention to logic function of the driver being used, as well as the labeling of the terminal on the device. For an on, space or logic 0 state, the driver's A terminal is positive relative to the B terminal. 4 (DI - the driver's input pin) is high, the output voltage on pin 6 (The A output) will be positive with respect to pin 7 (the B output). This helps to minimize the impact of electromagnetic interference, causing the voltage between the two wires to deviate.

It is usually a fairly simple matter to reverse the wires and test the communications again. A simple network of a PLC, VFD, and an HMI allows remote control of motors in an industrial setting. If you are pushing any limits, the termination resistor value has to be determined empirically for the individual network. This is why RS-485 states "The use of a cable termination is normally required".. With a reverse signal in the cable transmission is symmetrical, a small disturbance in the receiving device can also be an additional judge (for example, the signal receiving equipment, the use of A, B signal 90 ° phase difference, read the level of 10,11 , 01,00 four kinds of condition, counted as a valid pulse, this program can effectively improve the system anti-jamming performance (an accurate count)). This means that it is necessary to wait until the signal has stabilized before the bit can be sampled. Of course, many other problems can cause a communications failure and these will be addressed in the troubleshooting section. Unfortunately RS-485 section 4.5.3 states that the total load between "A" and "B" should be no less than 54 Ω. This section also defines the logic states 1 (off) and 0 (on), by the polarity between A and B terminals.

If you cherished this article so you would like to receive more info about what is rs485 cable nicely visit the web site.