• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is a nuisance. It can also be a chance to upgrade your glass to energy-efficient or insulated windows, and reap benefits like more comfort, higher potential for resales, and less bills.

It's a task you can do yourself for only a fraction of the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulate glass to improve the efficiency of your energy, reduce noise, and protect the historic integrity of your home's older. The windowpane replacement of windows is easy and can be completed by most homeowners who possess basic hand tools. Alongside a replacement pane, the following components are needed for the replacement process: latex glazing putty glazier's points; pliers; and the use of a heat gun to warm the old putty, if necessary. Before starting, put on gloves and safety goggles as working with broken glass may cause injuries.

Take away any broken glass pieces remaining. This can be done with a pair of pliers, though using a flathead screwdriver can also be effective in a pinch. After that, use a wood chisel, or putty knife, to remove the rest of the old putty from the frame and sash. Be careful to not scratch the Window Replacement Glass sash. Be careful and slow. It is a good idea to work on a sturdy ladder rather than on the ground and place someone on the sash to help hold it steady.

Prepare the window frame to receive the new pane when you have removed the old glue. Measure the width and height of the sash opening, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to an hardware store or home center, and get a piece of stock glass cut to size. You can also cut the glass yourself if have the right tools.

After installing the new glass After installing the glass, apply caulking on the edges. This will make the glass weatherproof. Install a glazier’s point on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they cause friction between the sash and the frame but they shouldn't be loose.

Before applying the putty, make sure to knead it until it's soft and free of lumps. Then make it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from corner to corner and ensure that it is even and smooth.

Glazier's Points

The glazier’s points are small triangular metal pieces that allow glass to be secured to the frame without causing any damage to the fragile surface. It's easy to understand how to use this nefarious tool, and you'll be able to save money on the expense of a professional installation.

After the old putty as well as glazier's points are removed Clean the frame thoroughly using a utility knife to remove any remaining residue. If necessary it is necessary to lightly sand the wood in the grooves of the rabbet to smooth rough spots. If you decide to sand the wood, be sure to protect it with painter's tape to avoid accidental damage.

Write down the dimensions of the frame. These measurements can be brought to a home center or hardware store, and the new frame will be cut to a smaller size. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane in the frame and push it into place firmly by using your hands. Then, use the tip of your chisel or back of the putty knife to tap in the glazier's points, as illustrated in Figure 11. When you're done, they should be flush with the top edge of the pane, and the raised shoulders of the points should be just below the rabbet's lip. groove.

Apply a thin layer of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Let it dry completely and cure.

When the glazing compound is dry, you're ready to install the new window sash. First, coat the wood with a thick layer of linseed. This will prevent the new putty from sucking up moisture and drying out and cracking over time. Use a brush to apply this coat, or the point of the blade. Then use the chisel that is on the back of the tool or the back of the handle to gently hammer the new sash or glazier's tip into the rabbet grooves. Repeat this process every 10 inches around the frame's perimeter.

Putty

A baseball thrown or a rock thrown by error, or a fallen tree can cause a broken or cracked window pane. Most windows can be repaired easily by installing a new piece. The glass is held in place by a small metal clip called a glazier's point, and putty, which is often called glazing compound. Before installing a replacement pane, first get rid of the old one and clean the area with the help of a rag, an abrasive scraper that is a pull type or an abrasive wood chisel. Wear safety glasses and gloves while working. You'll require a heat gun when the window is fixed into the frame.

If you plan to reinstall the original sash, gently remove the molding pieces that hold the old pane in place. Then you can sand the sash down to make sure it's flat and ready for new caulk. Once the sash is re-installed then, apply a new silicone caulk around the glass to ensure it won't leak or discolor over time.

Take out the glazing points in the rabbets. These are the grooves in the sash where the glass is. If they are hard to cut, place the hand tool, like a heat gun over them to soften first. When using a heat tool, be careful to avoid damaging the sash or its railings.

Prepare the bed for your new pane after you have removed the old glaze points and putty. Roll a rope with glazing compound between your fingers and then make it about 1/2 inch thick. Place it into the rabbets, where the glass will be put. The glass should rest against the putty on both sides. If needed you want to tap your glass lightly into the rabbet using your thumb.

If the new pane is cracked, you can use a silicone caulk or a glass glue that is based on solvents to seal the crack before pressing it into the sash. If the crack isn't sealed, you will need to apply putty to keep the water out. After the putty has dried clean the oily film off of the glass and let it dry completely before you paint. If you paint before the putty has completely dry, it won't form an effective seal and could leak or discolor over time.

Paint

If you've suffered a break in a window pane, then you may be concerned about the expense of a new one. But the truth is that replacing one glass pane does not require a huge amount of money when you do it yourself. Even double-paned windows can be replaced at a fraction of the cost it will cost a professional.

If you are working with large glass windows, first make sure it is securely attached to the frame. With the right tools and techniques you can complete this task easily and fast.

When you're ready to start with the removal of the old window by prying out the metal glazing points that are connected to it. These are tiny triangles of metal which act as "nails" to hold the window in the frame. They are submerged beneath a bead or glazing putty that sets to form a solid wedge that holds the frame in place and conceals the edges.

After removing the old pane, clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. These should be sanded down to the point of being bare, to allow you to paint them the same color as the rest the frame. After sanding the wood, apply a layer of flax oil. This will help to prolong the life of the frame.

Then, take measurements of the dimensions of the window opening. You'll need to determine the horizontal and vertical dimensions of the entire opening, as well as the thickness. To get the exact size of the new pane subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass replacement for window during seasonal change. You can take these measurements to a hardware store or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.