• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Pane Window Panes

A cracked window pane can be a nuisance. It could be a chance to upgrade your windows to energy efficient or insulated ones to enjoy benefits like increased comfort, increased resale values and reduced utility costs.

It's a project you can tackle yourself at less than the cost of hiring an expert. You'll need only the proper tools and a few minutes of your time.

Glass

Replace your single-paned windows with tempered insulation glass to improve energy efficiency, reduce noise, and maintain the original character of your older home. The procedure of replacing a window pane is relatively easy and can be accomplished by homeowners with basic hand tools. You will also need an extra window pane, glazier's suggestions, pliers, and latex glazing putty. If needed you can make use of a heat gun to warm the old putty. Wear safety glasses and gloves prior to beginning. Working with broken glass could cause serious injuries.

Remove any broken glass pieces remaining. This can be done with a pair of pliers, though using a flathead screwdriver can also be used in a pinch. Then, use a wooden chisel or putty knife remove the rest of the old putty from the frame and the sash. Be careful to not break the window sash. Take your time and work slowly. This can be done best on an elevated ladder, not on the ground. Also, ensure that someone below the sash ensure it is held steady.

Once you've removed all the old putty, it is time to prepare the window frame for the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of width and height. Take these measurements to an hardware store or home center and have a piece of stock glass cut to size. You can also cut the glass by yourself if you have the right tools.

After putting in the new glass, apply some caulking to the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on each side of the frame to secure the pane into the right place. The points shouldn't be so tight as to cause friction between the frame and replace window pane sash however they should not be too loose.

Before applying the putty, make sure to knead it until it is soft and free of lumps. Then make it into pencil-sized strips. Apply the first strip to the corner of the frame. Work from one corner to another, making sure it is even and Replace Window pane smooth.

Glazier's Points

The glazier's points are the small triangular pieces which help to secure glass into frames for windows without damaging or scratching the delicate surface. Understanding how to use these little helpers is easy and can save you money on professional installation or the cost of new glass.

After the old putty as well as the glazier's point are gone and the frame is thoroughly cleaned with a knife to remove any remaining residue. If necessary, lightly sand the wood along rabbet grooves to smooth out rough areas. If you sand wood, protect it with painter's tape to avoid accidental damage.

Take the dimensions of the frame and write down accurate measurements. Take these dimensions to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane into the frame and press it down with your hands. Utilize the chisel's point or the back of the putty knife to smudge the glaziers' points as illustrated in Figure 11. The glazier's points should be aligned with the top edge of the pane and the raised shoulders should be just beneath that lip.

Apply a thin bead of glazing compound on the edges of the new glass and in the rabbet grooves to seal and protect them. Let it dry and cure completely.

After the glazing compound dries and the glazing compound is dry, you can install the new window replacement near me sash. The first step is to coat the wood with an even layer of linseed. This will stop the new putty from taking in the moisture and drying out and cracking with time. Apply this coat using a brush or the tip of your putty knife, then employ the chisel or back end of the knife to gently hammer the new sash and glazier's tips into the grooves of the rabbet. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball that is thrown, an errant rock or a fallen branch can cause a window to crack or break. Fortunately, the majority of windows can be repaired by simply putting a new piece of glass in its the right place. The glass is held in place using tiny metal clips known as a glazier's point, and putty, also called glazing compound. Before installing a new pane, first get rid of the old one and clean the area with an abrasive and an abrasive scraper that is a pull type or an abrasive wood chisel. Wear gloves and safety glasses while working. You'll need a heating gun if the window is glued into the frame.

If you're planning to install your original sash, remove the mold that holds the old pane. Sand the sash until it is flat and ready to receive new caulk. After the sash has been put back in place, you can apply a silicone caulk over the glass. This will ensure that it doesn't leak over time or discolor.

Take out the glazing points in the rabbets. These are the grooves in the sash, where the glass is located. If they're difficult to work out, you can try holding the hand tool, such as a heat gun over them to soften them first. If you're using a heat gun, make sure not to cause damage to the sash or its railings by placing the tool too tightly.

After the old glaze points and putty have been removed make a bed for the new pane. Roll a rope made of glazing compound between your fingers, and then make it about 1/2 inch thick. Then, push it into the rabbets in which the glass will sit. The glass should rest against the putty on both sides. If needed gently tap your glass into the rabbet with your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. If the crack is not sealed, you'll need to apply putty to keep water from getting in. Once the putty is dry clean the oily film from the glass and let it dry completely before painting. Paint after the putty has dried completely. It will not make a strong seal and may discolor or leak over time.

Paint

You might be worried about replacing a broken piece of glass. However, replacing one glass pane does not need to cost a fortune when you do it yourself. Even double-paned windows can be replaced for a fraction of the price it would cost an expert.

First, if you are working on a large window, ensure that it is securely fastened to the frame. By using the correct tools and techniques you can make this task relatively easy and fast.

When you are ready to begin with the removal of the window pane. Take out the glazing points made of metal that are attached to it. These are small metal triangles which act as "nails", holding the window in the frame. They are placed under a bead or glazing glue that hardens to an unbreakable wedge that holds the frame in place and conceals the edges.

After taking off the old pane clean the frame and the wood. Scrape away any old paint and sand down the rabbet grooves, where the glazing points used to be. Sand them down to clean wood surfaces, so that you can paint the frames the same color. After sanding the wood you can apply a layer flax oil. This will help to prolong the life of the frame.

Then, take measurements of the dimensions of the window opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. Bring these measurements to a hardware or home improvement store and ask them to cut you the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.