• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will help prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and may even be fatal. You should take the time to ensure that your windows are in good shape.

For single pane windows it can be relatively simple to replace them, and the new window is usually able to fit into the old frame very easily. If you have double-paned windows which are held together by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need to source some plastic spacers that assist the new pane to fit correctly into the window frame.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass yourself. It is also a good idea to lay down a dropcloth before you start working on the glass, so that any shards will fall onto the fabric instead of landing on the floor, where they could be trampled upon and cause further damage.

Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and fix the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap between the door and the window is significant, you may prefer an alarm system that includes an opening. This will give you the best of both.

2. Sagging

upvc window repairs is a long-lasting and energy efficient alternative to timber sash windows. However, over time, they can suffer from a variety of problems including sliding. A sagging window in uPVC can cause problems with light, draughts, and even security. It is crucial to act immediately if you notice your uPVC windows are sliding.

Repositioning the hinges can help fix a window that is sliding. To do this, you'll need open the window so that you can access the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Once you've repositioned the hinges, shut your window and verify the fitting. If you're satisfied with the fit of your window, tighten the screws to hold them in the right position.

If you can't reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and dry out which causes their tightness to decrease. If this happens, it's important to replace the seal as quickly as possible to ensure your uPVC windows are watertight and draught-proof.

uPVC handles may also become loose. This is typically caused by screws that have become undone over time, but it can also be due to the mechanism of the handle wearing out. It's fairly simple to repair a loose uPVC handle. First, you'll need to close the window and perform a test fitting. The corner joints of the sash should align with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle and reverse the mechanism back into the position it was in.

3. Water Leaks

It is important to take action if you wake up every morning to find a smoky wall and wet floors. The leaks of water through windows could cause structural damage to your home, and affect your ability to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a simple fix that can be accomplished by any DIYer who is competent. Based on the severity of the issue the old caulking may require removal before a fresh layer can be applied. It is crucial to remember that when it is about uPVC window repairs you should not be tempted to 'over-caulk and then make the area more difficult to clean and reduce the efficiency of your energy.

Verify that the drainage holes are free of debris inside them and ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you may have to replace the window.

Other indicators of water leakage include rotted sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in damp conditions and can quickly spread across the house.

It is also important to note that if the leakage originates from the glass of your double glazed windows, upvc window repairs it's more likely to be a problem with the glass seal rather than the frame or sagging. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and blow open with ease, it may be hinges at fault. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Like any mechanical component, hinges can be damaged over time. It's very simple to change a window hinge but it's much easier if someone helps you to hold the frame.

Make sure that the uPVC hinges are open and closed in the proper direction. You can check this by looking for the arrows on each hinge, this shows which way the window should be opened.

The issue can be caused by opening the window improperly or a faulty installation in the factory. Sending us a photo through our website can often resolve the problem. We are always happy to provide advice.

It is also essential to grease the hinges regularly. This can be accomplished by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window to open and close more easily. It can also prevent corrosion and reduce the possibility of sticking. This is recommended to be done at least every year. WD40 and other solvent-based lubricants should not be used since they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by different factors. The hinges can also be unbalanced due to wear, causing a gap where the sash meets frame. They can be repaired by giving them thorough clean, however if they are beyond repair it may be necessary to get them re-aligned or replaced. The interlock, which is located on the hinge side of the window, may also become misaligned, again it is possible to give them a good clean, but in some cases it might be necessary to have these replaced.

These seals can wear down or become damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures, and also reduce the risk of draughts.

Another method of reducing drafts effectively is to use a Draught-excluder. These are typically fabric tubes filled with a filler, which can be hung over your window sill. They will keep your home warm by blocking cold air.

The windows made of upvc can keep providing excellent insulation and security in your home with regular maintenance and repairs. It is important to remember that all windows eventually become worn out, and it is more cost-effective to simply replace them rather than repair them. If you are experiencing issues with your Upvc windows, it is recommended to seek help from a professional immediately.