• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they do not rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help avoid unnecessary repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, making it very dangerous and potentially fatal. It is essential to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the new window will generally fit within the old frame very easily. However If you have double pane windows that are secured by internal beading it will be more difficult to remove the old panes and put in new ones. In this instance you'll need source some plastic spacers to help the new pane to fit properly into the frame of the window.

If you're planning attempt to remove the glass panes yourself it is crucial to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. It is also an excellent idea to lay down a drop cloth before you begin working on the glass, so that any shards fall onto the fabric instead of landing on the floor, where they could be trampled on and cause further damage.

Once the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to stop water and drafts from entering the home until a professional can come out and repair the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap is particularly large, you may want to consider using the security door with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. In time, they could develop a variety of issues, including sagging. A sagging window in uPVC can cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from getting worse.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll need open the window to access the frame. With an screwdriver, take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after having moved your hinges. If you're satisfied with the fit of your window, you can tighten screws to keep them in the right position.

If you can't reposition the hinges, you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loose their elasticity. It is essential to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. This is usually due to screws that have loosened over time, but it can be caused by the handle mechanism wearing out. Fortunately, it's easy to repair a loose uPVC window handle yourself. You'll first need to close the window and then perform an experiment fitting. The corner joints of the sash should be aligned with the casing joint. If it isn't then you can use a screwdriver to loosen the handle and then turn the mechanism back into its original position.

3. Water Leaks

It is important to take action if you get up each morning to find mouldy walls and wet floors. Water leaks from windows can not only cause degradation of your home's structure but also hinder your efforts to control the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a fairly simple fix that can be done by any skilled DIYer. Depending on the severity of the problem is, the old caulking may have to be removed. It is crucial to remember that when it is about uPVC window repairs, you should not be tempted to 'over-caulk and then make the area harder to clean and could decrease the efficiency of your energy usage.

Make sure that the drainage holes do not have debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious instances, you might need to consider replacing the window.

Moldy sills and rotten ones are other signs of water leakage. This is a fungus that thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to remember that if the leak originates from the glass of your double glazed windows, it is more likely to be a problem with the glass seal, home rather than the frame or sliding. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open in a breeze, it may be hinges that are at fault. These are easily repaired by any skilled DIYer and are usually done within a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that have hinges and like any mechanical part they are susceptible to wear and tear over time. It's easy to change the hinges on a window however it is easier if someone helps you hold the frame.

It is also important to ensure that the uPVC hinges are opening and closed in the right direction. Look for the arrows on each hinge to determine which direction the window should be opened.

The issue could be caused by opening the window incorrectly or by a poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are happy to give assistance.

It is also essential to ensure that the hinges are lubricated on a regular basis. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It can also prevent corrosion and reduce the possibility of sticking. This is recommended to be done at least every year. WD40 or other solvent-based oils should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also be unbalanced due to wear, causing a gap where the sash meets frame. If they are beyond repair, it could be necessary to have them realigned. The interlock may also become misaligned. It is located on the hinge's side, and might require to be cleaned. In certain instances it might be necessary to replace the hinges.

These seals can wear down or be damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. this will help in regulating indoor temperatures and will reduce draughts.

One of the most effective ways to cut down on the draughts in your home is to use a draught excluder. These are typically made of fabric which are filled with a type of filler. They can be placed on top of your windowsill. These will help to block out cold air and keep your home warm and cosy!

With a bit of regular maintenance and repairs your windows made of upvc will continue to provide excellent insulation and security for your home. It is essential to remember that all windows will eventually get worn out and it is more cost-effective to simply replace them rather than repair them. If you encounter any issues with your Upvc window it is recommended to speak with a professional immediately.