• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is an inconvenience. It can also be an opportunity to upgrade your glass to energy-efficient or insulated windows and replace Window pane reap benefits like more comfort, higher the value of resales and lower utility costs.

This is a project you could tackle yourself at only a fraction of the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

replace window Pane your single-paned windows with tempered insulation glass to improve the efficiency of your energy, reduce noise, and protect the historic integrity of your old home. The procedure of replacing windows is easy and can be completed by anyone with basic hand tools. You will also need an additional window pane, glazier's tips, pliers, and latex glazing putty. If needed you may make use of a heat gun to warm the old putty. Wear safety glasses and gloves prior to starting. Working with broken glass can cause serious injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers for this, but a flathead can be useful equally. Make use of a wood chisel or putty knives, to take away any remaining old putty around the frame and window sash. Be careful not to break the window sash. Work slowly and carefully. This is best done on a ladder, not the ground. Also, have someone on the ground to ensure it is held steady.

Make sure that the window frame is ready to accommodate the new pane when you have removed the old glue. Measure the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to a home center or hardware store to get an item cut from glass stock to the proper size. Alternatively, you can cut the glass yourself if have the right tools.

After putting in the new glass, apply caulking on the edges. This will make the glass weatherproof. Then install a glazier's point on the frame's opposite side to secure the pane into the right place. The points shouldn't be so tight that they cause friction between the sash and frame but they shouldn't be loose.

Before applying the putty to the surface, gently knead it until it is smooth and free from lumps. Cut it into pencil-sized pieces. Place the first strip to the corner of the frame, moving from one corner to the other so that it is smooth and even.

Glazier's Points

The glazier's points are the small triangular pieces which help to secure glass into a window frame without damaging or scratching the delicate surface. Understanding how to use these tiny pieces of help is simple and can save you money on professional installation or the cost of purchasing new glass.

After the old putty and glazier's points are removed and the frame is thoroughly cleaned with a knife to get rid of any remaining residue. Lightly sand the wood into the rabbet grooves to smooth out rough areas. If you sand wood, protect it with painter’s tape to prevent accidental damage.

Note down the exact dimensions of the frame. These measurements can be taken to the hardware or home center store, and the new pane will be cut to a smaller size. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new pane in the frame and push firmly using your hands. Utilize the point of the chisel or the back of the putty blade to tap in the glaziers' points as illustrated in Figure 11. The glazier's points should sit aligned with the top edge of the pane and the shoulders should be just below that lip.

Apply a thin layer glazing compound to the rabbet grooves as well as the edges of new glass. This will seal and protect the edges. Allow it to dry and cure completely.

Once the glazing compound has dried it's time to put in the new replacement window glass near me sash. First, saturate the wood with a thick coat of linseed oil. This will stop the new putty from sucking up moisture and deteriorating and cracking with time. Apply the coating using a brush this coat, or the tip of the blade. Then use the chisel on the back of the putty tool or the back of the putty handle to gently smash the new sash or glazier's point into rabbet grooves. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown at you or a rock that is errant or falling branch could cause a window pane to break or crack. Fortunately, windows can be easily replaced by simply putting a brand new piece of glass in its the right place. The glass is held in place using small clips made of metal called a glazier's point, and putty, often called glazing compound. Before you install a new pane, first remove the old one and clean the area with the help of a rag, the pull-type paint scraper or a wood chisel. Wear safety glasses and gloves when working. You'll require a heat gun if the window is glued to the frame.

If you plan to reinstall the original sash in the future, take care to remove the molding pieces that secure the old pane. Sand the sash until it's flat and ready to receive new caulk. Once the sash is installed, apply a new caulk made of silicone around the glass to ensure that it won't leak or discolor over time.

Take out the glazing points in the rabbets. These are the grooves in the sash where the glass is located. If they're difficult to cut out, try holding a hand tool like a heat gun over them to soften them first. When using a heated tool, make sure to not damage the sash's railings and sash.

Once the old glazing points and putty have been removed, prepare a bed for the new pane. Roll a rope made of glazing compound between your fingers, and make it about 1/2 inch thick. Place it into the rabbets where the glass will be put. The glass must rest against the putty on both sides. If needed gently tap your glass into the rabbet using your thumb.

If the new pane has cracked, you can use the silicone caulk or glass glue made from solvents to seal the crack before pressing it into the sash. If the crack isn't sealed, you'll need to apply putty to keep the water out. After the putty has dried and the film is oily, wipe it off the glass using the help of a rag. Allow it to dry completely before painting. If you paint before the putty is fully dry, it will not form a strong seal and may be leaking or discoloring in time.

Paint

You might be worried about replacing a broken piece of glass. However, replacing a single glass pane doesn't need to cost a fortune when you do it yourself. In fact windows with double glazing window replacement panes can be replaced at only a fraction of the cost of an expert.

If you're working with a large glass window first ensure it is securely attached to the frame. This task can be done relatively easy and quick with the right tools and techniques.

When you are ready to start with the removal of the window pane. Pry out the glazing points made of metal that are attached to it. These are basically small metal triangles which function as "nails" that hold the window in within the frame of wood. They are placed under a bead or glazing putty that sets to form an unbreakable wedge that holds the frame securely in place and hides the sharp edges.

After removing the old pane, clean the frame and the wood. Scrape off any paint that has been used and sand down the rabbet grooves in which the glazing points were. They should be sanded to bare wood so that you can paint them the same color as the rest of the frame. After sanding the wood, apply a layer of flax oil. This will help to extend its life.

Next, measure the width of the window's opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for Replace Window Pane seasonal changes in the glass. Take these dimensions to the hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.