• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged window pane can be an issue. It can also be an opportunity to upgrade your glass to energy-efficient or insulated windows and enjoy benefits such as greater comfort, a higher the value of resales and lower utility costs.

It's a project you can take on yourself for less than the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulated glass to increase the efficiency of your energy, reduce noise, and preserve the historic integrity of your home's older. The process of replacing the window pane is easy and can be accomplished by anyone with basic hand tools. Alongside a replacement pane, the following tools are required for the replacement handles for windows process: latex glazing putty glazier's points; pliers; and the use of a heat gun to warm the old putty, if necessary. Before beginning, wear gloves and safety glasses as working with broken glass may cause injuries.

Take away any broken glass pieces remaining. This can be done with pliers, though using a flathead screwdriver may be used in a pinch. Then, use a wooden chisel or putty knife remove the rest of the old putty from around the frame and the sash. Work slowly and carefully making sure not to break the current window sash. This should be done on a ladder, not on the ground. Also, you should have someone below the sash hold it steady.

Make sure that the window frame is ready to accept the new pane when you have removed the old putty. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Bring these measurements to the nearest hardware store or home center, and find a piece glass cut to size. You can cut the glass yourself if you possess the appropriate tools.

After putting in the new pane, run a small bead of caulking along the edge to make it weatherproof. Install a glazier's pointing on both sides of the frame. This will secure the pane. The points shouldn't be so tight that they cause friction between the frame and the sash However, they should not be loose.

Before applying the putty knead it thoroughly until it is smooth and free of lumps. Then you can roll it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to the next and ensure that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that allow glass to be secured into frames for windows without scratching or damaging the fragile surface. Learning how to use these hidden tiny helpers is simple and could save you money on professional installation or the cost of new glass.

After taking off the old putty, glazier points, and any other remnants clean the frame thoroughly with an utility knife. If necessary, lightly sand the wood along the grooves of the rabbet to smooth rough spots. If you sand wood protect it with painter’s tape to avoid accidental damage.

Take the dimensions of the frame and note down precise measurements. These measurements can be taken to a home center or hardware store, and the new pane will be cut a bit smaller. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Insert the new pane into the frame and push it in using your hands. Utilize the chisel's point or the back of the putty knife to tap the glazier's points, Replace Window Pane as illustrated in Figure 11. The glazier's points should be flush against the top edge of the pane and the shoulders should be just below the lip.

Apply a thin layer of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow this to dry and cure completely.

When the glazing compound is dry, you're ready to install the new window sash. The first step is to coat the wood with a thick layer of linseed. This will prevent the newly-created putty drying out or cracking as it absorbs moisture. Apply the coating using a brush this coat, or the point of the putty blade. Then use the chisel on the back of the putty tool or the back of the handle to gently hit the new sash, or glazier's point into the grooves of the rabbet. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball hit or a rock thrown in error or a branch falling can result in a cracked or cracked window. Luckily, most windows can be replaced by simply putting a brand new piece in the right place. The glass is held in place by a small metal clip, also known as a glazier's point and putty. This compound is also referred to as glazing compound. Before you install a new pane, first remove the old one and clean the area using an abrasive and a pull-type paint scraper or an abrasive wood chisel. Wear protective glasses and gloves while you do this work. If the window is attached to the frame, you'll need to use a heat gun to soften the adhesive before cutting it loose.

If you plan to reinstall the original sash, remove the molding pieces that hold the old pane in place. Then sand the sash to make sure it's flat and ready for new caulk. Once the sash is re-installed then, apply a new silicone caulk to the glass to ensure that it will not leak or change color in time.

Remove the glazing points from the rabbets and the grooves in the sash, where the glass is. If they're difficult to chisel, use the hand tool, such as a heating gun over them to soften first. If you're using a heating gun, make sure not to damage the railings or sash by placing the tool too tightly.

Once the old glazing points and putty are removed, make a bed for the new pane. Roll a rope with glazing compound between your fingers, and then make it about 1/2 inch thick. Then, push it into the rabbets, where the glass will be. It's important that the glass is positioned against the putty on both sides, so if you need to do so, gently tap the glass into the rabbet with your thumb.

If the new pane is damaged, you can use a silicone caulk or glass glue based on solvents to seal the crack before pressing it in the sash. If not, Replace Window Pane you'll have to apply putty over the crack to create an airtight seal and keep water out. Once the putty is dry clean the oily film off of the glass and allow it to dry completely before you paint. Paint before the putty is completely dry. It will not create a solid seal and may discolor or leak over time.

Paint

You might be worried about replacing a broken pane of glass. However, replacing one glass pane does not need to cost a fortune if you do it yourself. In fact, even a double-pane window can be replaced at a fraction of the cost of an expert.

First, if you're working on a large-sized window, make sure that it is securely fixed to the frame. This task can be made relatively simple and fast using the proper tools and techniques.

When you're ready to start, begin by removing the old window by prying out the glazing points made of metal that are connected to it. They are basically tiny metal triangles that function as "nails" that hold the window in place in the wood frame. They are submerged beneath a layer of glazing putty that transforms into a solid moulded wedge that holds the window firmly in place and hides the window's points.

After removal of the old pane clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. They should be sanded to bare wood, so that you can paint them the same color as the rest of the frame. After sanding, apply a coat of flax oil to the wood that is not sanded down to help extend its lifespan.

The next step is to measure the dimensions of the window's opening. You will need to measure the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure that you get a precise size for the new pane. This will allow for seasonal changes in the glass. Bring these measurements to your local hardware or home improvement store and have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.