• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to decay or rust as aluminum or timber.

It is essential to clean and oil UPVC windows and doors on a regular basis. This will reduce repair costs and UPVC window repairs increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, which can make it very dangerous and potentially fatal. You should take the time to make sure that your windows are in good shape.

Single-pane windows are relatively easy to replace and generally fit into frames that were previously in use very easily. If you have double-paned windows which are held together by internal beading, it will be harder to remove and replace the old panes. In this case you'll need to source some plastic spacers to help the new pane to fit perfectly into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not onto the floor, where they could be trampled under.

It's a great idea cover the gap with tape after the glass is removed. This will keep drafts and water from entering your property until a professional comes out to repair the window. This also serves as an obstacle to stop intruders from getting into your home. If the gap is particularly large, you may think about a security door that has an integrated window repair near me, since this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. However, over time, they can suffer from a variety of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from getting worse.

To fix a sagging window you can try to reposition the hinges. First, you'll need to open the windows so you can access the frame. After that, using the screwdriver, you'll be able to remove the hinges on the top and bottom and UPVC window repairs adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, close the window and verify the fitting. If you're happy with the fit, you can tighten the screws to ensure that they remain in position.

If you are unable to reposition the hinges, you might need to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to loosen. It is important to replace your seal as soon as you can to ensure that your uPVC window waterproof and draughtproof.

uPVC handles can also become loose. This is typically caused by screws that have been removed over time, but it could be due to the handle mechanism wearing out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to close the window and then perform a test fitting. The joint at the corner of the sash must align with the joint on the casing. If it isn't, you can make use of a screwdriver to loosen the handle and reverse the mechanism back into its original position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains, it is important that you take action. The leaks of water from windows do not only lead to the destruction of your home's structure but also hamper your efforts to regulate the temperature within your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame is damaged or missing.

It is a fairly easy fix that can be done by any competent DIYer. Depending on the severity of the issue is, old caulking may have to be removed. It is important to remember that when it is about uPVC window repairs, do not be tempted to apply too much caulk in order to make the area harder to clean and could reduce your energy efficiency.

Make sure that the drainage holes do not have debris inside them and that the sill pan has been properly angled to drain away from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in damp conditions and can quickly spread throughout the house.

If the leakage occurs between the double-glazed window, it is more likely that the issue is more with the seal than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or if it opens in a breeze. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that use hinges and, just like any mechanical component they can wear down over time. Changing a window hinge is essentially a simple process, but it's easier to do if you have someone to assist in holding the frame in place.

Check that the uPVC hinges are closed and open in the proper direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window a certain manner or because of poor installation at the factory. Sending us a picture through our website can often resolve the problem. We are happy to provide assistance.

It is also crucial to grease the hinges on a regular basis. This can be accomplished by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. This is recommended to be done at least once a year. WD40 and other solvent-based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges may also become disaligned as a result of wear, which can cause an opening between the frame and sash. This can be easily repaired by giving them good cleaning, but when they're beyond repair, it may be necessary to get them aligned or replaced. The second is the interlock, which is located on the hinge of the window and can also be misaligned, and again it's possible to just give them a thorough clean, however in some cases it might be necessary to have these replaced.

These seals can wear down or become damaged over time, allowing air escape. Installing high-quality weatherstripping will help to keep draughts at bay. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures and lessen the risk of draughts.

The last way to reduce the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler which can be hung over your window sill. They will help block out cold air and keep your home warm and cozy!