• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is a nuisance. It could also be a chance to upgrade your glass to energy efficient or insulated windows to reap benefits like more comfort, higher the value of resales and lower utility costs.

This is a project you could do yourself for less than the cost of hiring an expert. It requires the right equipment and an hour or two of your time.

Glass

If your single-pane windows are outdated damaged, cracked or deteriorating replacing them with modern insulated or tempered glass can improve energy efficiency and reduce noise while maintaining the historical integrity of older homes. The majority of homeowners with basic hand tools can Replace window pane a window pane. You will also require an additional window pane, glazier's tips, pliers, and latex glaze putty. If you need to you may use a heating gun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass can cause serious injuries.

Remove any broken glass pieces that remain. This is best accomplished with pliers, though using a flathead screwdriver can also be used in a pinch. Then, use a wooden chisel or putty knife remove the rest of the old putty from the frame and the sash. Take your time and work slowly and be careful not to break the current window sash. This is best done on an elevated ladder, not on the ground. Also, ensure that someone on the ground to hold it steady.

Prepare the window frame to accept the new pane once you have removed the old putty. Find the width and the height of the sash opening, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to the nearest hardware store or home center, and get a piece of stock glass cut to size. You can cut the glass yourself if you possess the appropriate tools.

After installing the new glass Apply a small amount of caulking around the edge. This will make the glass weatherproof. Install a glazier’s point on both sides of the frame. This will help secure the pane. The points should not be tight enough to create friction between the frame and sash however they should not be loose.

Before applying the putty on the surface, gently knead it until it is soft and free from lumps. Cut it into pencil-sized pieces. Apply the first strip to the frame's corner. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces that help secure glass into a window frame without scratching or damaging the delicate surface. It's easy to learn how to use this secret tool, and you'll save money on the cost of replacement windows uk of an installation by a professional.

After the old putty and the glazier's point are gone, thoroughly clean the frame with a utility knife to get rid of any remaining residue. Lightly sand the wood in the rabbet grooves if needed to smooth rough areas. If you sand wood, protect it with painter’s tape to protect it from damage caused by accidental sanding.

Take the dimensions of the frame and record precise measurements. Take these measurements to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane into the frame and press it in place by using your hands. Then, use the tip of your chisel, or the back end of the putty knife to make a tap on the glazier's points as illustrated in Figure 11. The glazier's points should be in line with the top edge of the pane and the shoulders raised should be just beneath that lip.

Apply a thin layer of glazing compound on the edges of the glass that has been made and into the rabbet grooves to seal and protect them. Let it dry completely and cure.

When the glazing compound is dry and the glazing compound is dry, you can install the new window sash. First, coat the wood with a thick coat of Linseed oil. This will keep the new putty from sucking in the moisture and deteriorating and cracking with time. Use a brush to apply this coat, or the tip of the blade. Then use the chisel that is on the back of the putty tool or the back of the handle to gently hit the new sash, or glazier's point into the grooves of the rabbet. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown in error, or a fallen tree could result in a broken or cracked window. The majority of windows can be repaired easily by putting in a new piece. The glass is held in position by a small metal clip, also known as a glazier’s point and putty. This compound is also called glazing compound. Before installing a upvc replacement window handles pane, first take out the old one and clean up the area using the help of a rag, the pull-type paint scraper or an abrasive wood chisel. Wear protective glasses and gloves when working. You'll need a heating gun when the window is fixed to the frame.

If you're planning to install your original sash, you must remove the mold that holds the old pane. Sand the sash until it is flat and ready for new caulk. Once the sash is re-installed then, apply a new silicone caulk around the glass to ensure that it will not leak or change color as time passes.

Take out the glazing points in the rabbets. These are the grooves on the sash where the glass is located. If they're hard to chisel, hold an instrument such as a heating gun over them for a few minutes to soften them. When using a heated tool, make sure to avoid damaging the sash or its railings.

Make a bed for your new pane after removing the old glaze and putty. Roll a piece of glazing compound between your hands, shaping it to be about 1/2-inch thick. Then, push it into the rabbets in which the glass will be. The glass should rest against the putty on both sides. If needed gently tap your glass into the rabbet using your thumb.

If the new pane has a crack you can fill it with a solvent-based glue or silicone caulk prior to pressing it into the sash. If the crack is not sealed, you will need to apply putty to keep the water out. After the putty has dried remove the oily film off of the glass and allow it to dry completely before you paint. Paint after the putty is completely dry. It won't form a good seal and could leak or discolor with time.

Paint

If you've suffered a break in a window pane, you may be worried about the expense of replacing it. But the truth is that replacing a single glass pane doesn't have to break the bank when you do it yourself. Even a double-paned window could be replaced for a fraction of what it would cost an expert.

If you're working with large glass windows first ensure it is securely fixed to the frame. Using the proper tools and techniques to complete this task easily and speedy.

When you are ready to start with the removal of the window pane. Remove the metal glazing points that are attached to it. These are tiny triangles of metal that act as "nails" to hold the window in the frame. They are submerged under a bead of glazing putty that transforms into a solid formed wedge that holds the window firmly in place and conceals the window's points.

After you have the old pane removed, clean up the surrounding frame and wood. Scrape off any old paint and sand the rabbet grooves where the glazing points were placed. Sand them to bare wood surfaces, so that you can paint the frames with the same shade. After sanding the wood you can apply a layer flax oil. This will help prolong the life of the frame.

Then, you need to measure the width of the window opening. It is necessary to measure the vertical and horizontal dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure that you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass in times of seasonal changes. Take these measurements to the hardware or Replace window Pane home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.