• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors wear out over time and will need to be replaced. When replacing them, it is crucial that the new handles match the dimensions of the handle that was previously used.

The top screw position the lever, and the keyhole size are the three measurements you need to check. Use the size guide to assistance in this.

Inline Lever/Lever

A lever/lever handle is a contemporary door handle designed to suit new or replacement doors. This type of door handle is available in a variety of styles & finishes. This handle is available from several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are constructed of durable materials and are suitable for multi-point lock doors that require a strong design. The handles are inline and run off the same spindle and screw fixings. They are easily installed on new or existing uPVC/composite door handles doors.

The handle can be adjusted and angled to fit all users. The handle has been endurance-tested to 200,000 cycles. This ensures that the finish is of high quality and performance will last for a long time. The sprung lever can be reduced to accommodate more locks. This is particularly beneficial for narrower door frames where the cylinder is further back. A shortened lever is also a good choice for doors that have latches that can be activated by the thumb turn on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently to the lever type handles that are found on the majority of doors. These handles are operated by one spindle or two spindles inline or offset. They are typically used on UPVC doors with double glazed handles glazing and come in a variety of finishes and variations.

The handles are available in various finishes, including White chrome and Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with the best performance and durability to serve the purpose it was designed for.

All UPVC handle lever pads include a spindle and screws and can be installed on the uPVC door. The 211mm backplate fixing centres allow for a wider size of handle which is often a benefit when replacing a damaged or worn multi point door lock mechanism. These handle levers have springs, which can solve the issue of door handles that sag out of horizontal position when not being used.

It is essential to match the PZ dimensions for both the multipoint lock as well as the uPVC doors when selecting the replacement double glazing window handles UPVC spindle and handle. This measurement can also be called 'handle centre or cylinder centres'. It is important to match the right handles.

Once you have decided on the correct PZ size it is important to make sure that the push and lever pads are designed to fit the American with Disabilities Act compliant handles that you need for your door. These are typically round or square, with an internal lever, and an external push pad.

The majority of UPVC Lever Pads that we sell are spring-loaded. This means that they will return to a horizontal state when not being used instead of hanging, and possibly securing to the frame. This prevents draughts from entering the home. It is also the case that the majority of the UPVC lever pad handles are hand-operated, allowing you to install them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. They work by using a key to unlock a cylinder that will reveal pins that can be aligned with those inside the lock body, allowing them to turn an revolving cam, opening the door. Euro Cylinders can be fitted with up to six pins with both internal and external doors usually having different levels of security.

The choice of the correct cylinder is essential; it is dependent on the way your door and handle are utilized. For instance, doors that are external should be fitted with a more secure cylinder while internal doors can be secured with the standard cylinder. Some cylinders have extra features that can increase security, for instance, anti-drill or anti-bump properties.

To make sure that the euro cylinder is the right size for your door, it should be measured accurately. The cylinder must be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn, if there is one. If you cannot measure using the lock in its position, you can remove it. It is crucial to ensure that there is no cylinder that extends beyond the handle or escutcheon. This could make it susceptible to lock snapping attacks.

Most newer cylinders have been designed with anti-drill and bump resistance features built into their design. These are designed to reduce attack chances by forcing the cylinders to turn in a different direction. This will help to deflect attacks and protect your door.

There are cylinders that have been designed to resist snapping. This is a typical attack on cylinders. A special tool is used to break the break line of the lock and then the front of cylinder is snapped off. This is much quicker and less difficult than opening multipoint locks. It also leaves no evidence of a burglary, which can impede an insurance claim.

Spring Cassette

This spring cassette is found within the base plate of your door handle. It offers a spring-loaded solution to return your multipoint lock handles to their normal position after use. These handles used to have no spring and would drop when the locking mechanism was disconnected. This simple feature is among the best ways to correct this and it is also an effective way to keep your doors made of upvc from getting stuck in the open or closed position, as they aren't always easy to manually close by hand.

These spring cassettes are specially designed for use with sprung multipoint locks but they won't work with multipoint handles that are not sprung and you must have a hole specifically cut in the backplate to allow them to fit (please check the image for a technical diagram). These cassettes can be used as a replacement to broken or missing cassettes on the backplate of uPVC door handles. They have a square cut-out that accommodates an 8mm spindle and are available in a variety of.

These spring cassettes provide a great value solution to the issue of door handles that are sagging. They are simple to install and can extend the life of your uPVC door. Please contact our team to learn more about our range of uPVC accessories and spares. We are always ready to provide expert advice and to assist you.