• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Door Hinge a Loose Door Hinge

Repairing a broken door hinge is a simple task for most homeowners. If, however, the holes for screws are smashed and won't hold screws you may need to put in wood glue and dowels before you can install the hinge.

Brush away any surface that has rust. This will allow the dowels to remain in place and provide them a solid foundation to rest on.

Removing the Hinges

Many standard door hinges can be removed, which makes it easier to move a door from one side of the frame to the other side or take the entire door off if necessary. Anyone with a bit of patience can take the hinges off, but you need to know what to do.

If the hinges are painted you'll need to get rid of the paint before attempting to remove the pins. If you don't, the paint could flake off and scratch your door when you try to lift it. To break the seal put the hinges into an stainless steel pan and fill the pan with water until the hinges are fully submerged. The hinges should rest in the pan for 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

After the pins are loosening and the pins are loose, you can take off the hinges from the door and frame. You can make use of a screwdriver to get the job done, but it is recommended that you use a magnetic screwdriver for this project. This type of screwdriver is designed to remove screws made of steel and will make the project go much faster.

Before you attempt to remove the hinges it is recommended to spray them with a lubricant. A simple lubricant will help you speed up the process and remove the pins and screws more easily. You can find this type of lubricant at most hardware and home improvement stores.

Keep in mind that the number of door hinges you will need will vary depending on the door's type and its settings. Doors with solid cores and heavy weights will require more hinges, whereas hollow-cored doors that are lighter may only need two or three.

Understanding the different kinds of hinges will help determine which one is best for your situation. Exterior hinges are designed to withstand the weight of a door, while interior repair window hinges need to be able support lighter loads.

Reattaching the Hinges

Sometimes a door hinge will become looser over time and begin to hang out of alignment or sag. This can cause problems but is usually easy to solve. In most cases an easy tightening of the screw will fix the issue. However in the event that the screw holes have been stripped out, this can be more difficult. A wood dowel could be used to tighten these holes once more.

Start by drilling out the hole you had previously made using the drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a secure fit, the dowel should be cut at the same length as the screw. Install the screw again and tighten it to the desired degree of tightness. If the door continues to have an tendency to get stuck and close, then you can add another dowel to the gap and repeat the procedure. Make sure to close the door slowly to verify the clearances at the perimeter after each adjustment.

You could also use a wood plug instead of the dowel. It works just as well but might take a little longer to put in. Simply whittle a chunk of wood to the proper size to ensure a secure fit, then tap it into the hole. If you don't have a wooden tool you could also make use of toothpicks or wooden matches as well.

After you have reinstalled the new screw then use a countersink to make the hole for the head of the screw smaller so that it won't rub against the edge of the door when it's open and closed. This will make it easier to tighten the screw when installing the hinge.

After installing the double glazed window hinge repair again, you should apply lubrication to the hinge using a dry lubricant. This will help to prevent it from getting stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent alternatives. Apply a thin coating and allow it to soak into the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're not yet ready to replace your hinges, you can try a few fixes. Make sure the screws that secure the hinge plate in place to the door frame and the frame are tight. If they're loose, tighten them with the help of a screwdriver or a power drill. Be careful not too tighten the screws, as this could cause gaps to appear at the trim joints, or worse, strip out the threads.

If the problem is the hinge plates are splitting and you want to reattach the plates by putting wood glue to the back of them and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will provide a solid base for the screws and help prevent the plates from shifting when you drive them into place. Let the glue dry before reattaching the hinge.

The screws may also be damaged or missing. This can be corrected by replacing the screws. Use a drill that is the same size as the screw hole to prevent drilling into the hinge or jamb.

After you've reattached your hinge, close the door and look at the gap between the frame and the door. The gap should be the thickness of a penny or less if an older door was hung incorrectly. If the hinges were set up properly, this shouldn't be an issue.

If the hinges are still loose, try adding an extra thick hinge between the surface of the hinge plate and the mounting surface. This will give the hinges more space. You can also try removing the hinge pin from the problematic hinge and pounding it down using a hammer to make it tighter or use a new hinge pin altogether. You can also lubricate your hinges using mineral oil or jojoba in order to reduce friction and hold them in place. Lubricating your hinges periodically can keep them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

The friction caused by a upvc window hinge replacement cost's constant movement draws dust particles. These particles can become stuck and build up in the moving parts of door hinges if they are not maintained and cleaned regularly. In the end the hinge becomes stiff and creaky and its appearance may get worse. Regular cleaning, lubrication and inspection can help preserve the quality of hinged door and ensure their proper function.

Examine the hinges for signs of the accumulation of rust. If the corrosion has reached the point of destroying the surface of the hinge barrel or screw holes, you will require replacement upvc hinges of the hinges. If you are able to save the hinges, remove any loose rust by using steel wool and wire brush. Then, apply a commercial rust remover or a homemade solution such as lemon juice on the hinge. Let the solution that removes rust sit on the hinges for a few minutes in order glass to glass hinges penetrate and dissolve the remaining rust.

Retightening screws can help restore hinge function If you don't wish to spend money or time to replace hinges. If you've stripped the screws however, it could be necessary to add an wooden dowel or shim to the hinge. Dowels made of wood are available in round rods of various lengths and sizes. You can purchase them on the internet, at woodworking supply shops and home improvement centers.

A shim could also be made from a piece of plastic or metal, based on the type of hinge you have. To make a dowel cut a piece made of wooden dowel or other sturdy material to the desired size. You can then dip a dowel in carpenter's glue and then insert it into the hole. The glue will hold the dowel securely in the desired position.

Before cleaning the hinges put down a cloth or towel to protect your flooring from spills. After protecting the area, clean the hinges using an easy sponge or cloth that has been dipped in mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. A small brush or toothbrush can be used to access hard-to-reach areas in crevices and narrow areas.