• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Window Sash Repairs

Window sashes must be checked regularly for mold, mildew and other damage. By catching these problems early you will save money on future repairs.

The sash is an inside frame that is able to move vertically up and down in windows that open. This article will teach you how to perform easy repairs to your sash.

Weather Stripping

Wooden window sashes can give an elegant appearance to your home. They are also sturdy and can last many years if they are properly maintained. However, they can become damaged or degraded in time due to exposure to elements and wear and tear. Fortunately, sash repair specialists can bring your windows back to their original condition and maintain their appearance for much longer than newer replacement windows.

The first step to sash window repairs (see post) is addressing weather stripping, which is found on both the sash as well as the frame. It can cause drafts if damaged or is loose. Begin by identifying the upvc window repair's brand and the date of manufacture for the glass (etched on the glass's corner, or the aluminum spacers between panes). Then, remove the sash and mark its height and width so that you can locate the appropriate weather stripping replacement to match.

Then, remove the sash and place it on a table so you can access all four sides. If your sash has been double glazed window repairs-hung, remove the ropes and weights that should fall into the pocket in the jamb lining. After removing the sash using the utility knife, you can remove the weather stripping from the old sash by hand or with a putty blade.

When the sash is clean and clean, you can put in the parting stops. These are long pieces that separate the sashes. Pam prefers standard 1/2-inch by 3/4-inch window trimming from the lumberyard. But, you can also substitute for a scrap piece of lumber.

After removing the stopper and cutting it to length, apply a thin coat of glazing compound over the bottom of the sash. Smooth the compound with your putty knife, then let it dry for at least a day. Once the putty has fully cured and dried, you can apply an acrylic latex topcoat. This coating will protect the putty and give your sash a fresh look.

Sash Hardware

The hardware that holds window sashes is susceptible to wear and tear due to age and use and the result could be a door or window that isn't able to open or close easily. It's important to know that replacing and fixing this hardware is usually easy and affordable. If a sash is difficult to operate try spraying lubrication into the jamb channel, and then slide it open to see if that resolves the issue. If the issue persists, it is most likely the sash balance. You'll need to take off the window sash in order to reach this hardware.

Ideally, window sashes should be able to open and close with very little effort, however, this can be difficult when the weights wear out or if the sash meeting rail isn't properly coated. This issue could be caused by a variety of things, such as lack of maintenance or by an incorrect weight rating for a particular sash.

If the hinge arms of a window begin to sag, this can cause the sash to drag and eventually strike the frame in the corner that's directly opposite the hinge arm (Photo 1). To resolve this issue, first make sure the sash is firmly seated in the opening of the frame and then take it out of the window. If the sash is secured to the hinge arm, you'll have to loosen the hinge arm and replace it (Photo 2). Then, put in the new sash (Photo 3).

Old windows, particularly those in older homes, can be difficult to close and open due to hinges that are sagging and general inefficiency. In most cases, a few simple repairs can transform these windows into smooth operation again and save the homeowner money on energy bills.

To complete these repairs to sash it is essential to have all of the necessary tools lined up before you begin. Begin by marking the position of the hinge channel on the frame using pencil (Photo 1). This will make it easier to place the channel in the proper place when you are finished. Take the sash off and then remove all hardware including the parting beads, cords, and chains that hold the sash in place. Soften any putty that has been hardened with an electric heat gun set to medium and fitted with a shield for the nozzle. Take off the old sash and put it in a bag with a label.

Sash Weights

Whether your window sash repairs are to replace a damaged cord or simply to keep your windows functioning by replacing worn out weights on sash can improve sash operation and cut down on the energy cost. Sash weights are composed of heavy lead or iron cylinders that are encased inside a concealed cavity, and connected by a rope to the movable window sash. These weights act as counterbalances and allow you to open and close the window without the need for mechanical or electrical devices. If they fail, sashweights are usually neglected or not used by homeowners.

It is difficult to recover a sash-weight that has fallen from the cavity, so you'll need to find one that fits correctly. You will also require an additional piece of string, a length of the sash cord, as well as some sash pulleys to tie the new sash weights to the sash cord.

Older windows made of wood are joined with mortise and tenon joints. The wood pegs that hold the components together can be removed using the use of a pin punch and hammer. The majority of these pegs are big on one side and smaller on the other. It is important to remove first the smaller diameter sides. Sashes made later in the century made use of glue instead of pegs. They can be separated by cutting through the glue line with an instrument, and then tapping the mortised part loose with mallets.

Once the sash has been removed, you can take off the sash stops and gain access to the pockets for weights. This is typically done by drilling tiny holes in the bottom of each jamb. The hole is then covered with an access panel made of wood which can be removed to allow you to see the inner workings of the frame.

After the sash has been stopped and the access panel removed, you'll be able to remove the weight of the old sash and replace it with new. First, weigh the sash to ensure that the weights you have may not be the correct size. After the new weight has been installed, thread a string through the sash pulling mechanism. Then, you can attach the string to the boxed frame. Leave a few inches protruding at the top of the string to allow future adjustments.

Sash Cords

In most old double glazed window repairs-hung window, a chain or cord is attached to the weights. This helps keep the sashes within the jamb level. Over time, these cords may become damaged and render it impossible to raise the windows. A new sash cable will give you the ability to raise and lower the sash, and keep it in position when opened.

To replace sash cords the first step is to remove the access panels from the jambs. They are usually screwed or nailed into and need to be removed. It is possible to remove them using an axe or hammer, but it is always best to lay out dust sheets before beginning any work.

Once the access panel is removed, you can start working on the sash. Utilize a flat bar or chisel to pull the narrow partsing beads out of their grooves. It is important to be patient as they're often placed in a wedge or nail. If the sash is in place, break the mortise and tenon joints with a hammer and pin punch or screwdriver, and then take out the wood pegs on the components. The sash should be able to move freely now, but it might require some lubrication to feel less stiff.

With the sash in an open position Take a measurement of the sash chain to extend from the pulley in the top of the jamb to the sash slot in the bottom. Cut the chain or cord and secure it as in the previous step. You can employ a hammer, screws or nails, however nails are less likely to cause damage.

It is recommended to keep the weights that came with the original counterbalance unless you have purchased a kit that will replace the counterbalance that was previously installed. It's cheap to purchase them from a salvage store and they will be easy to install once you've got the sash open. Depending on the dimensions and shape of your window repairs near me you might need to install one or two sashweights to keep it open.