• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged or cracked window is an inconvenience. This can be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap advantages like improved comfort, higher resale value and reduced utility bills.

It's a task you can tackle yourself at a fraction of the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

Replace your single-paned windows with tempered insulate glass to improve energy efficiency, cut down on noise, and protect the original character of your older home. The procedure of replacing windows is simple and can be done by anyone with basic hand tools. You will also require a replacement window pane, glazier's tips pliers, and latex glazing putty. If necessary you can use a heatgun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass could cause serious injuries.

Take out any broken glass replacement windows pieces that remain. It is recommended to use pliers, but a flathead can work equally. Then, use a wooden chisel, or putty knife, to remove the remaining old putty from around the frame and the sash. Be careful to not scratch the window sash. Be careful and slow. It is recommended to work on a stable ladder rather than on the ground and to place someone on the sash to help hold it steady.

Once you've removed all the old putty, it is time to prepare the window frame to fit the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Bring these measurements to a hardware store or home center, and get a piece of stock glass cut to size. Alternatively, you can cut the glass yourself, if you have the appropriate tools.

After installing the new pane After installing the new pane, apply a small amount of caulking around the edge to make it weatherproof. Then, place a glazier's tip on each side of the frame to secure the pane in place. The points shouldn't be too tight that they cause friction between the sash and the frame however they shouldn't be too loose.

Before applying the putty on the surface, you must knead it thoroughly until it is soft and free of lumps. Make it into pencil-sized strips. Place the first strip to the corner of the frame, working from one corner to the other to ensure it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces that allow glass to be secured into a window frame without scratching or damaging the delicate surface. It's easy to understand how to use this secret tool, and you'll be able to save money on the cost of an installation by a professional.

After getting rid of the old putty glazier points, and any other remnants clean the frame thoroughly using a utility knife. If needed it is necessary to lightly sand the wood along the grooves of the rabbet to smooth rough areas. If you sand Replace window pane wood cover it with painter's tape to prevent accidental damage.

Take measurements of the empty frame and write down accurate measurements. These measurements can be brought to an hardware or home centers store, and the new pane will be cut a bit smaller. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane in the frame and press it into place firmly using your hand. Then use the point of your chisel or back of the putty knife to pierce the glazier's points as shown in Figure 11. When you're done taping, they should be in line with the top edge of the pane and the raised shoulders of the points should be just below the rabbet's rim groove.

Apply a thin layer glazing compound to the rabbet grooves and Replace Window Pane the edges of new glass. This will protect and seal the edges. Allow it to dry and cure completely.

Once the glazing compound has dried it's time to put in the new window sash. First, coat the wood with an even layer of linseed. This will stop the new putty from soaking in the moisture and deteriorating and cracking with time. Apply this coat with a brush or the tip of your putty knife, then employ the chisel or back end from the putty knife to gently hammer in the new sash and glazier's points into the grooves of the rabbet. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball hit, a rock thrown in error, or a tree falling could result in a broken or cracked window. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in position by a small metal clip, also known as a glazier’s point and putty. This compound is also known as glazing compound. Before installing a replacement pane, first remove the old one and clean up the area with an abrasive and an abrasive scraper that is a pull type or an abrasive wood chisel. Wear gloves and safety glasses while working. If the window is secured to the frame, you'll need to employ a heat gun in order to soften the adhesive before taking it off.

If you plan to reinstall the original sash, remove any molding pieces that secure the old pane. Sand the sash until it's flat and ready to receive new caulk. Once the sash is installed and sanded, apply a fresh silicone caulk around the glass to ensure it will not leak or change color as time passes.

Remove the glazing points from the rabbets. These are the grooves in the sash where the glass is located. If they're difficult to chisel, hold the hand tool, such as a heatgun over them to soften first. When using a heating tool, be careful to not damage the sash's railings and sash.

After the old glazing points and putty are removed, prepare a bed for the new pane. Roll a rope of glazing compound between your fingers, and make it around 1/2 inch thick. Then, press it into the rabbets in which the glass will be. It's important that the glass is positioned against the putty in all places on each side So if you have to tap it, gently press the glass into the rabbet using your thumb.

If the new pane has a crack then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. Otherwise, you'll need to putty over the crack to create an airtight seal and keep water out. When the putty dries then clean the oily film off the glass with a rag and allow it to dry completely prior to painting. If you paint before the putty is fully dry, it won't form a strong seal and may leak or discolor over time.

Paint

If you've experienced a broken window pane, you may be concerned about the expense of replacing it. But the truth is that replacing one glass pane does not have to break the bank when you do it yourself. Even a double glazed replacement windows-paned window could be replaced for a fraction of the price it will cost an expert.

If you are working on a large-sized window, make sure it is securely fixed to the frame. Using the proper tools and techniques, you can complete this task easily and quick.

When you are ready to start taking down the old window pane. Remove the glazing points made of metal that are attached to it. These are basically small metal triangles that act as "nails" that hold the window in place in the wood frame. They are buried beneath a layer of glazing putty, which is then cured to form a solid, moulded wedge which holds the window in place and hides the edges.

After taking off the old pane clean the frame and the wood. Scrape away any paint and sand down the rabbet grooves where the glazing points were. These should be sanded to bare wood, so that you can paint them the same color as the rest the frame. After the sanding process, apply a coat of flax oil to the wood that is not sanded down to extend the life of the frame.

Then, you need to measure the size of the window's opening. It is necessary to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will allow for seasonal changes in the glass. Bring these measurements to a hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.