• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a Subaru Spare Key

If you lose your Subaru car key, you should call a locksmith. Usually, they can cut new keys for you for less than the dealer.

Fob remote "push to start" intelligent keys or a simple metal key are the two most popular types of Subaru car keys. The Fob key has to have its chip changed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes work with a keypad inside your car to communicate with the computer system in your vehicle.

Subaru models come with a lesser known feature called PIN Code Access. You can make a custom number sequence to start and open your vehicle. Refer to the owner's manual for learn how to utilize this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's possible that the battery in the key fob has gone out. The first thing you'll need to check is that the battery is in good condition, and you can do this with a small remote tester or an ordinary multimeter in your garage.

The next step is to remove the circuit board for the transmitter from the key fob and then examine it. The board will contain one or two sets of 8-digit numbers, so write down the first set so that you will be able to remember it later. Once you've completed this, you can begin programming the key fob at home. The process for doing this varies depending on the model and year of your vehicle however it's generally easy enough to do by yourself.

Key Fobs

Subaru's latest models have key fobs which not only unlock doors, but also turn on lights, lock gas cap and even start the car. That last trick is especially beneficial if your experience includes arriving at the pump only to find that your car won't start because the key fob battery was dead.

It doesn't matter if your Subaru is old or new, it's likely that the key fob can be replaced without difficulty. It's important to keep in mind that more recent models with an advanced level of technological advancement may require a trip to the dealership. With little effort and some time, you can create your own replacement key fob.

Begin by opening the case and inspecting the circuit board of the transmitter. (Instructions on how to open the case are usually included in the owner's guide). There should be one or two serial numbers that have 8 numbers each. Write down the initial number series and save it to refer to later.

Then, sit in the driver's seat. Close all the doors. Turn the key 10 times to start your car, then turn off the engine. Press the lock button on your key fob, then open the door. This will ensure that your doors are functioning properly. Then close the door, and take the key out of the ignition. The car should beep again, indicating that the key fob has been programmed.

Ignition System

The key battery may be dead If your Subaru keys don't work as they should. If you know How to get a spare subaru Key, you can replace subaru key the battery of your key fob yourself. A replacement battery is cheap and easy to locate. If your keypad doesn't respond to your commands, there could be another problem. To find a spare key, you should go to an authorized dealer. They will guarantee that the key is a genuine Subaru key that's covered by warranty and it'll be programmed to your vehicle. This is a lot simpler and safer than buying an aftermarket key from a retailer online.

The dealer will also cut a key for you if you give them your VIN number and as evidence of ownership. This information is used to identify the replacement key so that it can be accepted by your immobilizer. This procedure is more complicated than cutting a new key and the dealer will generally charge more for this service.

After the new key has been programmed, you'll be able to change it over to your existing key. It takes only five seconds to insert the second key, which is why it's vital to have an operational key in your pocket. You can remove the key after the security light has stopped flashing and test it.

Battery Replacement

Subaru fobs are extremely useful since they can switch on the power windows and sunroof of your car with just one button press. However, the battery inside the Subaru key fob was not made to last forever and will eventually need to be replaced. This short guide from Capitol subaru replacement key fob will help you to replace the battery yourself.

You'll first need to find the small crack that divides the front from the back of your keyfob. You can open this seam with the flat-head screwdriver, which will reveal the small compartment that contains the battery. Remove the old battery and then replace it with a fresh one, making sure it is facing the correct side up. After you have put everything together you can use the new key fob to lock, unlocking, and starting your vehicle.

You should always have a spare set keys, especially if yours is broken or has been lost. A new key can be bought at your local dealership for cars or you can get one cut from the locksmith. It is essential that your key fob works correctly as soon as you can to ensure that you are able to drive safely.