• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat remote key replacement Key Programming, Http://Www.M-Bp.Jp/, 500 Key Fob Won't Work

A key fob for Fiat 500 allows you to easily open doors and start your car. However, there are many reasons the fob could stop functioning. These include a dead battery damage to the receiver module, problems, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob won't function is due to the battery is dead. Modern key fobs have a limited range of operation, and must be within some feet of the car to operate. If you're far away from your vehicle and you press the key fob button, the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.

You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The parking lights should light up and the key fob should operate the lock and unlock switch.

If your key fob still does not work after replacing the battery, it may be water damage which has prevented it from connecting to the module in your vehicle. Water damage can occur in a number of ways, from a light splash to submerging your fob in salt water at the beach. If you believe your fob was exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, your fob is likely to need to be reset by an experienced auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean or wash it in a washer. Saltwater is particularly dangerous to the circuit board of the fob that can cause it to short out and eventually die. If you get the fob wet, it's not a good idea but if you accidentally drop it into a glass of water or do not remember to take it out of your pocket before you run the washer Don't give up hope.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or a similar product. Next try the fob and check if it functions. If the fob doesn't function, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is a bit older and has not been programmed for your car, you will need to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith needs to cut the key to match the ignition on your vehicle. They'll also have to reprogram the fob to your vehicle's system. This is an affordable and quick process that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob won't be functioning is because it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function it could be due to an internal circuit board problem. Reprogramming the fob typically resolves this problem. You can find instructions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

You may need to replace the metal retaining clips that keep the coin battery. If they lose tension, it could hinder the battery from sitting properly and could cause the remote to malfunction.

In rare cases the fob might become disconnected from your vehicle due to software issues or hardware issues. This could be a huge issue, but you are able to often fix this by visiting an auto locksmith to reprogram your fob. In certain instances it is possible that the software will need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This can occur when the key fob is in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons why the key fob could not function could be due to a weak connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands which are then read by the vehicle.

Fortunately, there's an easy method to reset all of the onboard systems in your 500 device, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and then restart the car's computers, which could help get your key fob working again. If the issue continues it is recommended that you consult an experienced technician. They can identify the root cause of any problems.