• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they don't get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will prevent unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows it is fairly easy to replace windows, and the new one will usually fit inside the old frame very easily. If windows with double glazed window repairs panes are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this instance it is essential to buy plastic spacers to help the new pane fit into the window frame.

If you're planning to attempt to remove the glass panes yourself, it is essential to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth prior to you begin working on the window panes so that any shards fall onto the fabric and not onto the floor and could be trampled under.

It's a great idea tape the gap once the glass has been removed. This will keep water and drafts from entering your home until a professional comes out to fix the window. This will also provide a barrier to prevent any criminals from getting into your home. If the gap is particularly large, you may want to consider using an alarm door that comes with an integrated window, as this will offer the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash window. Over time, they can be affected by a variety of issues such as sagging. A window that is sagging can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from getting worse.

To fix a window that is sagging you can try to reposition the hinges. To accomplish this, you'll have to open the window so that you can get to the frame. Then, using a screwdriver, you can remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have moved your hinges. If you're happy with the fit, tighten the screws until they remain in the right place.

If you are unable to reposition the hinges, you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loosen. It is essential to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles could also become loose. This is often caused by screws that have loosened over time, but it could also be due to the handle mechanism wearing out. It's fairly simple to fix a loose uPVC hand. The first step is to close the window and then perform an experiment to ensure that it fits. The corners of the sash need to be aligned with the casing joint. If it doesn't, you can use the screwdriver to loosen up the handle. Then turn the mechanism to position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains, it's crucial to take action. The leaks of water from windows do can not only cause degrading of the structure of your home but also hinder your efforts to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on how severe the issue is, the old caulking may have to be removed. It is crucial to remember that when it is about uPVC window repairs, do not be tempted to 'over-caulk' as this will only make the area more difficult to clean and can reduce your energy efficiency.

It is essential to ensure that any drainage holes are free of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious cases you may need to think about replacing the window.

Moldy sills and rotten ones are another sign of water leakage. This fungus thrives under conditions of dampness and can spread quickly throughout the home.

It is also important to remember that if the leakage originates from the glass of your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sagging. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open with ease It could be the hinges that are at the fault. Any competent DIYer can replace these in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that are hinged and, just like any mechanical component they will wear out over time. It is essentially a very simple process but it can be easier to do when you have a person to assist in holding the frame in place.

Make sure that the uPVC hinges are closed and open in the proper direction. Check for the arrows on each hinge to determine which way the window should be opened.

Faulty window hinges could be caused by improperly opening the window in a particular way or due to inadequate installation at the factory. Sending us a photo via our website will often solve the issue. We are more than happy to offer suggestions.

It is also essential to grease the hinges regularly. Applying an engineering lubricant that is light to the hinges is a great method of doing this. We suggest using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the possibility of a window sticking and help prevent corrosion. The ideal time to do this once a year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by different things. First, the hinges due to wear and tear may become displaced, which will cause gaps to develop between the sash and the frame. If they are beyond repair, it may be necessary to get them re-aligned. The interlock may be unbalanced. This is located on the hinge's side, and may need to be cleaned. In some instances, it may be necessary to replace these.

The next most common reason for draughts is window seals, these can become worn down or damaged over time and allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures and will reduce the risk of draughts.

Another, and most effective ways to cut down on the draughts in your home is to use a draught excluder, these are usually fabric tubes which are filled with a type of filler. They can be positioned on top of your windowsill. They will help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can remain a great source of insulation and security to your home with regular maintenance and repairs. It is crucial to recognise that windows last for a certain period of time and there may come the point when it's more efficient to replace them than fix them. So, if you're having issues with your upvc windows, it is always recommended to seek help from a professional as soon as you can.