• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional upvc window repair repairmen work from high above the ground, moving massive glass panes. They adhere to strict safety guidelines and frequently work in extreme weather conditions.

Wearing protective clothing, remove the metal glazing points and the glazing putty by using a utility knife. A heat gun may help soften the old putty and speed up removal.

Replacement

When a window's pane is broken, it may be tempting to try and repair the glass instead of replace it. However, replacing windows is usually more cost-effective and may aid in preventing other issues with your home's energy efficiency. Examine the type of broken glass to determine whether it's a temporary fix or if a permanent solution is required.

The first step to repair broken windows is to remove the sash, or frame and lay it flat on a table. Wearing eye protection, gently wiggle the window's pane and remove any remaining shards. Then, use a utility knife to peel off the glazing compound as well as the glazing points that keep the glass in the position. Keep track of the components and where they are so that they can be put back in place.

After the frame and sash have been removed and the frame is removed, you can begin preparation to install new glass. Be sure to check that the opening of the frame is the proper size for your replacement window. To allow for expansion and contraction of the glass and frame and contraction to both directions, measure the opening and subtract 1/8 inch. Then, purchase double-strength glass that are cut to these exact dimensions. It is recommended to purchase enough glazier's clips, or points to place them every 6 inches around each window pane.

Depending on the window's warranty, this may be covered by the manufacturer and in this case, you must contact the company to file a claim. Once the new glass has been installed, it should be sprayed with a thin coating of the compound used by glaziers. After the compound has dried, you can paint the frame to match.

If your crack is longer than an inch in length you can stop it from expanding by slicing a small arc just beyond the crack. This trick won't be infallible, but it will slow the development of the crack to a manageable amount until you can take permanent measures.

Repair

Professional window contractors know how to deal with a variety of glass, and they have the tools needed to complete a proper job. They are able to dispose of waste properly and are therefore less likely than other contractors to leave behind a mess that could inflict harm on family pets or members of the family. They're also used to working with different types of windows, and they may be able to spot problems that aren't obvious to the uninitiated homeowner.

Wear safety goggles and gloves prior to beginning the process of repairing damaged glass. A small crack could cause glass shards to fly and put anyone at risk within or around the home. It's also crucial to determine the cause of the crack in the first place, as it can help prevent future problems.

Make a two-part mixture of epoxy. These are usually 50/50 mix of resin and hardener, and they must be mixed quickly. When the mixture is prepared put it in the crack in the glass and allow it to dry. This should only take about a minute however it is important to work quickly since the mixture is very thick and fast drying.

Once the epoxy is dried, you can get rid of any excess with a putty knife. The next step is to clean around the cracked glass. If you don't do it properly, the residue can cause further damage to the glass. Use a putty blade smooth out the compound around the window's edge and match it to the wood frame.

For a more durable solution think about using a plastic covering. A trash bag that is heavy-duty or tarp is ideal, but you can also use masking tape to cover the glass. This will prevent the crack from spreading, and will also keep wind, water and insects out.

If you're not able to get to the window fast enough then you can apply silicone sealant to create an interim repair. Simply apply a small amount of the substance around the outside of the broken pane. It won't completely seal the gap between the frame and the glass completely however it will keep the break in place until you are able to fix it.

Repainting

If your windows with glass are old, you may consider repainting them. This is a cost-effective alternative to replace windows and give your house a new look. Before painting, make sure the surface is clean. Use rubbing alcohol or soap and water to remove oil smudges, as well as other residues which can prevent paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your fingers onto the glass. Apply multiple thin coats instead of one thick coat. This will make the paint last longer, and ensure that your windows appear smooth and even.

If you're planning to repaint your glass windows, make sure you have all the right tools at hand. You'll need a brush or sponge, painter's tape a ruler, toothpicks, and a few other tools, such as paper towels or a rag. You should also have the paint and brushes you'll need for the project in your possession. Make sure you follow the manufacturer's instructions and be prepared with plenty of patience as it can take a while for the paint to dry.

If you are using solvent-based paint, you should also ensure that the room where you work is well-ventilated. This will reduce the chance of breathing in harmful chemicals and allow the paint to dry faster. It is also important to ensure you have a protective mask for any spray paints you apply.

You'll need to wash the glass window thoroughly with soap and warm water before you paint it. Clean the glass window thoroughly using soap and warm water. You can then use rubbing alcohol to clean off any grease or oil that could affect the adhesion of the paint. Make sure that the windows are dry before you begin painting them.

If you have energy efficient double pane windows on your windows, it might be possible to file a claim for repair or replacement with the window company or dealer who sold them. This is especially the case if you've experienced multiple problems with cracked glass or condensation while the windows are still covered by warranty.

Sealing

If you have double-pane windows with a broken seal or a newer version of insulated glass units (IGUs) that have experienced defogging or fog, there are many options for fixing the problem. The most costly option is to replace the insulated unit and frame however it could be necessary if condensation or fog cause energy loss. Other alternatives include replacing the current IGU with a single pane or repairing it by drilling a small hole through the bottom of the unit, and then filling the solution with anti-fog.

You can also close the gap between a window frame and a sill or threshold using a felt strip or vinyl v-strip. Felt can be stapled, glued or put in place, but it does not offer much protection against moisture. Vinyl v-strip weather stripping is durable and simple to install however, it can be expensive and is generally used for areas that are subject to abrasions that are high. Door sweeps are cheap and can be put into place, but they create little to no barrier between the sill or threshold and dust, air and other debris.

To repair a cracked window seal, first use a putty blade to take off the old caulk. Wearing eye protection and gloves take care to remove the glazing points -- tiny fasteners that hold the glass to the frame's recess, with sharp, pointed ends. After removing the glazing points, scrub the grooves and sand the wood until it is smooth. Clean any sanding dust and then seal the unfinished wood surface using a linseed oil-based paint or clear sealer.

Traditional glazing putty is applied using either a putty knife or a caulking gun, however using a knife allows for a more efficient precision and precise application. It also will provide a better seal. Select a putty made specifically for glass, since it will last longer and stick better.

Apply a thin bead of the putty to the inner edge of the frame where it touches the glass. Slide the window into the frame in a way that the scribed line on glass aligns with edge of frame. Apply pressure on the glass to compress the putty and create a tight seal. Smooth the compound using fingers that are gloved, and wipe away any mistakenly applied caulk or spills that are not properly wiped away before it is dry.