• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane can be a nuisance. This could be an opportunity to upgrade your windows to energy efficient or insulated ones and enjoy advantages like improved comfort, increased resale value and reduced utility costs.

This is a project you could tackle yourself at a fraction of the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

If your single-pane windows are old damaged, cracked or Replace Window Pane deteriorating replacing them with modern insulated or tempered glass can improve energy efficiency and reduce noise while preserving the historic integrity of older homes. A majority of homeowners with hand tools can Replace window pane a window pane. Alongside a replacement pane, the following components are needed: latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty if required. Wear safety goggles and gloves before you begin. Working with broken glass could cause serious injuries.

Take out any broken glass pieces remaining. It is best to use pliers however, a flathead may be useful equally. Then, use a wood chisel, or putty knife, to take the remainder of the old putty from around the frame and sash. Take your time and work slowly making sure not to damage the old window sash. This can be done best on an elevated ladder, not on the ground. Also, have someone lower to ensure it is held steady.

After you've removed all the old putty, prepare the window frame to accommodate the new pane. Measure the width and height of the opening for the sash and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to the nearest hardware store or home center and have a piece of stock glass cut to size. You can cut the glass yourself if you have the appropriate tools.

After installing the glass, apply caulking on the edges. This will make the glass weatherproof. Then, you can install a glazier's pointing on each side of the frame to hold the pane in place. The points shouldn't be so tight that they cause friction between the sash and the frame, but they also shouldn't be loose.

Before applying the putty on the surface, knead thoroughly until it becomes soft and free from lumps. Roll it into pencil-sized strips. Place the first strip in the corner of the frame, moving from one corner to the next to ensure it is smooth and even.

Glazier's Points

The glazier's points are small triangular pieces of steel that help secure the glass to the frame without causing any damage to the fragile surface. Knowing how to use these little helpers is easy and can save you money on a professional installation or the cost of new glass.

After taking off the old putty, glazier points, and any other residue, clean the frame thoroughly with an utility knife. If necessary it is necessary to lightly sand the wood along grooves of the rabbet to smooth rough areas. If you decide to sand wood, cover it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and write down accurate measurements. Take these dimensions to an hardware store or home center, and have the new pane made slightly smaller than the frame's opening. This will ensure a snug fit and leave room for expansion and contraction.

Insert the new pane into the frame and push firmly using your hands. Then use the point of your chisel or back of the putty knife to make a tap on the glazier's points as shown in Figure 11. When you're done, they should be in line with the top edge of the pane and the shoulders of the points should be below the lip of the rabbet groove.

Apply a thin layer of glazing compound on the rabbet grooves and the edges of the new glass. This will protect and seal the edges. Allow it to dry completely and cure.

When the glazing compound is dry, you're ready to install the new window sash. First, coat the wood with a thick layer of linseed. This will keep the new putty from taking up moisture and drying out and cracking over time. Apply the coat using a brush or the tip of your putty knife, and then use the chisel or the back end from the putty knife to gently hammer the new sash and glazier's point into the grooves of the rabbet. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball that is thrown, an errant rock or a fallen branch can cause a window to break or crack. Fortunately, windows can be easily replaced by simply putting a new piece of glass in its the proper place. The glass is held in place with a small metal clip called a glazier's point and putty, also called glazing compound. Before installing a replacement pane, first take out the old one and clean the area using the help of a rag, the pull-type paint scraper or the wood chisel. Wear gloves and safety glasses while working. If the window is glued to the frame, you'll need to use a heat gun to soften the adhesive before taking it off.

If you are planning to install your original sash, remove the molding that supports the old pane. Sand the sash until it is flat and ready to receive new caulk. Once the sash is re-installed, apply a new caulk made of silicone around the glass to ensure it doesn't swell or fade in time.

Take out the glazing points in the rabbets. These are the grooves on the sash, which is where the glass is located. If they're difficult to cut out, try placing a hand tool like a heat gun over them to soften them before you do. If you're using a heated gun, be cautious not to damage the railings of the sash or the sash itself by using the tool too closely.

Create a bed for your new pane after removing the old glaze points and putty. Roll a rope of glazing compound between your hands, shaping it to be about 1/2-inch thick. Then, press it into the rabbets in which the glass will rest. The glass must be positioned against the putty on both sides. If necessary gently tap your glass into the rabbet using your thumb.

If the new pane has damaged, you can use the silicone caulk or glass glue that is based on solvents to seal the crack prior to pressing it in the sash. If the crack is not sealed, you'll need to apply putty to keep the water out. After the putty is dry then clean the oily film off the glass with an abrasive and allow it to dry completely prior to painting. Paint after the putty is completely dry. It will not make a strong seal and could leak or discolor with time.

Paint

You might be worried about replacing a damaged piece of glass. But the truth is that replacing one glass pane does not have to break the bank If you can do it yourself. Even a double-paned window can be replaced at a fraction of the cost to replace windows uk it would cost for a professional.

If you are working with large glass windows first, ensure that it is securely fixed to the frame. This is relatively easy and fast using the proper tools and techniques.

When you are ready to begin taking down the old window pane. Take out the glazing points made of metal that are attached to it. These are tiny metal triangles that act as "nails" that hold the window in place. They are submerged under a bead of glazing putty that is then cured to form a solid, formed wedge which holds the window in place and hides the edges.

After removal of the old pane clean the frame and the wood. Scrape off any old paint and sand the rabbet grooves in which the glazing points were. Sand replace window pane them down to clean wooden surfaces so you can paint the frames the same color. After sanding the wood, apply a layer of flax oil. This will help to extend its life.

Then, you need to measure the size of the window opening. You'll need to determine the vertical and horizontal dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass during seasons of change. You can take these measurements to a hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.