• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 key fob programming 500 Key Fob Won't Work

A key fob from fiat 500 replacement key cost 500 makes it simple to open doors and start your car. There are a myriad of reasons the key fob might stop working. These include a dead battery, damage to the receiver module, water issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Modern key fobs have a very limited range of operation, and must be within some feet of the vehicle to operate. If you are far from your vehicle and you press the key fob button, the car will not respond, and will display an "Key fiat 500 Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery in the coin cell (Part number CR2032) with a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. You can find them at the local hardware store or on the internet.

After you've replaced the battery in the coin cell You can test it by standing close to your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should work the lock and unlock buttons.

If the key fob won't work after replacing the battery, it might have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can happen in a variety of ways, such as the simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If that doesn't work the fob might require reprogramming by a professional auto locksmith or the dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the fob's circuit board, causing it to short out and eventually end up dying. It's not a good thing to soak the fob in water however, don't give it up when you accidentally drop it in water or forget to remove it from your pocket.

First, remove the battery. Before replacing the battery clean the electronic chip using isopropyl or similar products. Check the fob to see if it is functioning. If the key doesn't work, it may need to be reprogrammed. This is usually done by a professional or dealer auto locksmith.

If the key you have is older and has not been programmed for your vehicle, you will need to replace it completely. This is a straightforward process which can be accomplished by a professional automotive locksmith. The locksmith must cut the key to match the ignition in your vehicle. The locksmith also needs to reprogram your fob in the car's system. This is a cost-effective and fast process that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob might stop functioning is because it's out of range. The remote has a range of 30 feet. So when you're too far away from your vehicle, it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If your fob doesn't work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button", it may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob will solve the issue. You can find directions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

It is possible to replace the metal clips that hold the coin battery. If they lose tension it could prevent the coin battery from sitting properly and can cause your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software issues or hardware issues. This can cause a major trouble, but you could frequently fix this issue by visiting an auto locksmith to reprogram your fob for you. In certain instances it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could happen if the key fob is close to an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob may not work due to a bad connection with the buttons, key fiat 500 water damage or damage to the internal chips.

If the key fob has been unable to function for a while without notice or even after trying every option at home to resolve it e.g. replacing the battery, reprogramming it and using the spare key fob, you might have a defective receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery of 12 volts for about 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electrical charge and restart the car's computers, which can help you get your key fob working again. If the issue continues, you should seek out an expert technician. They can identify the root cause of any problems.