• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. They don't decay or rust as timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large amount of damage to your home, which can make it very dangerous and potentially fatal. It is essential to ensure that your windows are in good condition.

For single pane windows, it is relatively easy to replace them, and the replacement will usually fit inside the frame of the previous one easily. However If windows with double glazing window repair panes are held in place by internal beading, it'll be more difficult to remove the existing panes and install new ones. In this instance it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

If you are going to try to remove the window panes yourself, it is essential to wear appropriate safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric, not onto the floor and could be trampled under.

It's a great idea to tape the gap once the glass has been removed. This will keep drafts and water from entering your home until a professional comes out to fix the window. It also acts as a barrier, preventing any intruders from getting access to your home. If the gap is large, you might think about an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they are susceptible to a range of problems including sliding. A sagging window can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from becoming worse.

To fix a window that is sagging you can try repositioning the hinges. To accomplish this, you'll have to open the window to access the frame. With a screwdriver, you can unscrew the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after having moved your hinges. If you are happy with the fit of your window, you can tighten screws to secure them in place.

If you can't reposition the hinges, Repairs to uPVC Windows you might require replacing the seal. Over time, rubber seals lose their elasticity and dry out, which causes their tightness to decrease. If this happens, it's important to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and safe from drafts.

uPVC handles may also loosen. Most often this is due to screws that have become loose over time. However, it can also happen because the handle mechanism has been worn out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need close your window and do an initial test fit. The corner joints of the sash need to be aligned with the casing joint. If it does not, you can use the screwdriver to loosen the handle. Then, turn the mechanism to position.

3. Water Leaks

If you awake to wet floors and mouldy walls every time it rains it is important that you take action. Windows that leak water do are not just a cause for degrading of the structure of your home but also undermine your efforts to control the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the problem the caulking used previously might need to be removed before a fresh layer can be put on. It is crucial to keep in mind that when it is about uPVC window repairs you should avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and reduce the efficiency of your energy.

Make sure that the drainage holes have no debris inside them and ensure that the sill pan is properly angled to drain away from the window. In more serious situations, you might need to consider replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. This is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double glazed windows repairs-glazed glass, it is more likely the issue is with the seal than the frame. This can be easily fixed by an uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with ease it could be the hinges that are at the fault. They can be repaired by any skilled DIYer and can usually be completed in just a few minutes.

Like all mechanical parts, hinges can be damaged over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is simpler if you have someone to help hold the frame in place.

It is also worth checking that the uPVC hinges are being opened and closed in the right direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The issue could be caused either due to opening the window in the wrong way or a faulty installation in the factory. Sending us a picture via our website will often resolve the problem. We are happy to give assistance.

Regularly lubricating the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window open and close more easily. It can also stop corrosion and decrease the chance of sticking. It is recommended to do this at least once a year. WD40 and other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of various factors. The hinges can also be unbalanced due to wear, causing gaps where the sash meets frame. If they are damaged beyond repair, it may be required to realign them. The interlock, which is located on the hinge side of the window, can be misaligned. Again, it's possible to give them a thorough clean, however in some instances it could be necessary to have these replaced.

The seals may wear out or be damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help in regulating indoor temperatures and again will reduce the possibility of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler, which can be placed over your window sill. These will keep your home warm by blocking out cold air.

With a little maintenance and repair, your upvc windows will continue to provide excellent insulation and security for your home. It is crucial to recognise that windows last for a certain period of time and they may reach a point where it is more economical to replace them than fix them. If you have any problems with your upvc window, it's best to consult an expert as soon as you can.