• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet to go in and out as they please without you needing to let them in or out. They can also help prevent your cat from urinating inside the home.

It is simpler to install a cat flap on a upvc panel than one made of glass but you'll need some skills and the right tools.

Take a measurement of the door

The installation of a cat flap inside the door can be a challenge however, as long as you use the correct type of cat flap make sure you take your time and follow the instructions provided it shouldn't be a problem. We will help you mark the shape and use the jigsaw to cut the door area. Then, we'll finish the job by affixing the flap. This will ensure that the flap is in place and protects the doors from the damage caused by rain and wind.

To determine the size of the cat flap you need, measure the width of your pet. This will ensure that the flap is large enough to allow your pet to enter and leave the house without needing to open and close the door every time, yet small enough to keep them from going too far in either direction.

If your kit has an illustration of the location to drill then you can place it on the door and then use a pencil around it. If your door has moulding or sill on the bottom edge ensure you have enough clearance from these as this will ensure your cat's safety and prevent them gaining access to your home.

Next put on your eye protection as well as a dust mask and using a jigsaw start cutting according to the lines you penciled in. Don't press the blade too hard as this can cause it to cut more quickly than you would like it to. Utilize a set square to ensure you are cutting the material correctly and that the cut is a rectangle shape. When you are happy with the result, you are able to take the door material off.

Draw a Line

The cat flap is a great way to allow your pet to go in and out without having to worry about them being a nuisance to guests or leaving unwanted gifts inside the home. It also reduces drafts and helps to keep the temperature inside your home steady. Installing a cat flap on your door might seem difficult to those who haven't done it before. Many people call an expert carpenter or joiner to complete the job. It is an option, but you can do it yourself if your tools are right and the steps are adhered to.

While this is much simpler with a wooden door, it is still possible in uPVC doors, but you must be careful not to scratch the doors since this could invalidate the warranty. First, you need to take measurements of the door to make sure it will accommodate the new fitting cat flap in upvc door panel-flap. If you have an ordinary uPVC panel, this should be easy. However in the case of composite or a different type of door, you may need to be more careful.

The next step is to determine the height of your cat's stomach. This is the distance between the floor and the underside of your cat's stomach. It is important to find an area at the entrance that will allow your pet to move through easily. Once you've figured out the measurements, you'll need to mark the area with a spirit-level and a pencil, so that you are certain that the opening will fit your cat.

Once you've marked the area, it's time to cut the hole. It is crucial to take your time and use a jigsaw to ensure that the cuts are clean and smooth, not rough and uneven. This could damage your door. It is also important to wear safety glasses and a dust mask at all times when working with the jigsaw as inhaling the sawdust could be hazardous to your health. After you've completed the cutting, you'll have to smooth the edges of the hole with sandpaper, so that the cat flap can be fitted easily into place.

Make a hole

Getting a cat flap fitted to an existing door panel or double glazing sealed unit is quite difficult. If you are not very skilled in DIY, it's best to employ an expert to do the job for you. A botched job may not just be ugly, but also an enigma for security as well as allowing cold air to get in when the cat is outside and hot air to escape inside.

The first thing to do is draw the location of the hole in the door with a pencil and a spirit level, this will ensure that it is properly placed and runs flush with all the other parts of the door. It is important to have a piece of sandpaper at ready for any rough edges.

Wear any safety gear you'll need to use the power tool. If you are concerned about the noise of the jigsaw, you can purchase a cordless version which is quieter and simpler to use.

You should only remove the material that is required to create the flap. It is important to leave a little extra material for the wall thickness of the flap. However cutting away too much could cause issues or even damage the frame of the door.

A door made of upvc could contain a metal frame or a panel inside that could interfere with the microchip cat flap and if this is the case, you'll need to cut an over-sized hole to ensure that the metal does not touch the the cat flap. If this is the case, it is important to fill in the gap and render it watertight.

If you are fitting cat flap In upvc door Panel an animal flap to an upvc door or a double glazed window with a frame made of metal, you'll need to talk to a professional who can supply you with a new glass pane with the hole for the cat flap in it. It is cheaper to do this than trying to fix the flap to an existing pane of glass that hasn't been designed specifically for the purpose.

Place the Flap

Cat flaps allow your pet to move around at their own pace, giving them the freedom to relax inside the house whenever they want to. However, if you own a uPVC door it can be difficult to fit an animal flap, especially if you don't own glass panes that could be cut to accommodate one. If you are willing to install a half-glazed upvc door panel cat flap replacement upvc door panel with cat flap panel, it is possible to add the cat flap. It's not as simple as simply cutting a hole through the door though and there are a few things you'll need to take care of first to ensure it's safe.

A uPVC, GRP or composite door panel usually has a flimsy plastic outer skin joined to a soft polystyrene core that is insulating. It is crucial to be careful when cutting the material. This type of door usually has a template which you can use as a reference to cut the hole in the door.

Once you've marked the opening in your front door, it is time to put in the cat flap. You can pick from a wide range of options, from simple push-button units to microchip activated ones that allow your pet in. Whatever kind of cat flaps you select it is essential that your cat can use the flap without getting stuck outside in the rain.

It's a good idea to select circular fittings instead of a square one, as circles are more securely cut into the door glass. This is because square holes make the glass more susceptible to cracking if a drill is used on it. This is also a safer option, as you won't have to drill into the toughened glass that could shatter and harm your pet or family. This is especially important if there are children or elderly people in your home who might be injured by glass shards.