• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, the wear and tear can cause lock malfunctions. There are a few simple steps you can take to restore the security of your uPVC door.

These quick fixes will ensure your home is secure, whether you realign the lock or clean the mechanism.

Clean the Lock

double glazed patio door repairs doors are ideal to let the outdoors inside and keeping the elements out. However, they can be risky for security when the lock isn't functioning properly. As time passes, wear and tear, hot and cold weather dirt and debris could take their toll on the lock of your local patio door repairs door and cause it to become difficult to open. With a little care you can ensure that the lock on your patio door always functions properly.

To begin with, it's crucial to clean the lock on your patio door and all of its moving parts. This helps to get rid of any grime and coatings that could be preventing the lock from functioning in the way it should. Start by wiping all the moving parts of your patio door lock using a damp cloth. Then apply a scouring pad or a rough damp cloth to scrub the dirt-infested areas of the door and frame. Then wipe the lock with a dry cloth to get rid of any moisture. Allow it to air-dry before you use it.

If you have an exterior door that is fitted with pin tumbler latch mechanisms it is possible to lubricate the lock by applying powdered graphite to the key or using a lubricant made of Teflon, like WD-40 Multi-Use. This type of lubricant is easy to apply and it doesn't dissolve with time. If you're unable find the right lubricant for your lock, you can make use of a pencil with a larger tip. Put the pencil into the lock and move it around to spread the graphite.

Regular maintenance is also required to keep the tracks of sliding patio doors free of dust, dirt and other debris. These tracks are especially susceptible to snow and ice, which could cause them to jam or bind which makes it difficult for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing damaged or dirty weather stripping and cleaning them before installing it. The same can be done to patio door rollers which can be wiped down and then sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC french doors, similar to sliding patio doors, work using 3-4 or sometimes five-point locking mechanisms, which include the lock cylinder and handle operated by a key. These doors also require maintenance, specifically lubrication on the moving parts. This can be done with an oil that is thin (never WD40) and should be done once per year.

If hinges that are sagging aren't the cause, the door could be misaligned and caught or hitting the strike plate hole in the frame. Remove the strike plate and use a sharp tool to expand the mortise. This allows the latch to sit perfectly in the hole and avoids scratching or catching on the frame.

When the cylinder is out of the way take a measurement of its width using the help of a book or piece wood that fits into the gap between the adjustment screw and the lock. The outer dimension is measured from the outside of the door how to repair tilt and slide patio door the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door latch isn't able to turn even after cleaning and lubricating, there's a possibility that it is out of alignment with the strike plate hole. Make sure that your door is in a balanced position, and if the hinge screws are secure. In a lot of cases, however, simply moving the strike plate upwards or downwards will fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to properly engage. In this case, enlarge the opening with an hammer and chisel. Then test the latch to ensure it does not rub against the door jamb frame or catch the frame.

You should identify the type mortise lock you currently have before purchasing an alternative. This can be done by looking at the end faceplate and noting whether it is square or round. Then, look at the screw holes on the existing lock and note the size of each one. This information will allow you to locate a replacement lock that is the exact same width and will fit into the hole that you already have.

You'll need to locate the mortise lock and inspect it for bends, scratches or other damage that requires to be repaired. A damaged or bent latch is more likely break than one that hasn't been used much, so be sure to replace the lock with a brand new, secure version in the event you notice any signs of damage or wear.

Once you've decided on the kind of lock replacement you need, it's now time to start the actual repair. Remove the old handle and spindle from the patio door, and then put in the new one. Begin by installing the handle in the interior, aligning it with the spindle, and then fixing it with the two screws or bolts that secure it. Once the handle's interior is installed, you can install the exterior handle and screw it into the position as well. Once you have completed these steps check the handles to make sure they can be shut and open easily and that the latch engages correctly with the strikeplate.

Check the Strike on the door.

The strike plate and the door latch are two parts which work together to secure the door. An incorrectly aligned strike plate and door latches can cause the latch to not latch the door properly. Fortunately, this issue is often easy to fix.

Examine the holes that receive the strike plate to ensure they are clear of obstructions such as dirt or plastic plugs. Remove the screws that hold the strike plate. This allows it to move vertically, but not separate it from the frame. Adjust the strike plate to align its receiving holes with the latch hooks of the door latch. After the strike plate has been adjusted, tighten the screws and then test the door to determine whether it locks smoothly after the new adjustment.

These plates are difficult to reach for homeowners with sliding patio doors. However they are crucial for locking and unlocking your door. These plates are usually located on the top and bottom of the door jamb which is where they are used to support the door's latch. The door latch is able to slide into the strike plate to create a seal when closed. If the strike plate has been damaged, rusted, or is not installed correctly the latch may not properly lock the door.

A misalignment of the latch and strike plate is one common cause for the patio lock not to close or remain in place. The easiest method to check for this is by performing the "lipstick test." Rub some lipstick on the outside of the deadbolt and put masking tape on it. The lipstick will leave an impression when you close the door. This will indicate exactly where the latch meets the strike plate. If the mark is too high or low you can easily alter the strike plate.

The sliding patio door locks keep your home safe from intruders, and if they're not functioning correctly, you should fix the problem quickly. By following these easy steps, you can fix your patio door's lock and get it back to normal within a short time.