• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are several reasons why the ignition of your car could be locked. One reason is that the key is dirty or has a damaged wafer inside it. You can fix it by sliding the key in and out of the cylinder several times.

The pins of the lock cylinder may also be stuck. You can tap the cylinder gently with a small tack-hammer.

Check the Battery

If your car is in Park or neutral, but won't turn on when you insert the key into the ignition, there may be an issue with the shifter switch for the transmission. It is possible to fix the issue by shifting the gear shifter up or down to get the vehicle into the correct gear.

If the car is still unable to turn, the problem could be due to the neutral safety cable, or the shifter in the transmission. These can be easily fixed by a mechanic, or a local automotive locksmith.

It is also possible that the ignition cylinder is worn out. In time the ignition as well as the key can wear out, making them difficult to remove or insert. A lubricant like silicon lock grease can address this problem, allowing the wafers slide into place.

The lint in your pocket and the adhesive from tape that holds packages together can also build over the key, which prevents it from being able to slide into the ignition. You can clean the keys with a cloth or a cleaner such as Triflow to resolve this issue. It is also recommended to utilize a spare key in order to determine if the issue is with the ignition or the ignition.

You can also try to tap the key using a small hammer when it's in the ignition. This will create a tiny vibration that could cause enough vibration to loosen the wafers inside the ignition and allow them to slide into the right position. You should be careful not to harm either the ignition cylinder or key.

If all of the above methods fail, it's probably time to call a locksmith or automotive mechanic to examine the issue. It could be that the key is damaged in the ignition, or it could be the time to replace the entire thing. If the problem is with the key the locksmith will be able to make a new one for you. If the cylinder for the ignition is the issue then you'll have to take your vehicle to a repair shop in order for it to be replaced. These problems are usually easy to fix.

Check the steering wheel

A common issue that can hinder the ignition from turning is the steering wheel being locked. It can happen if drivers accidentally engage the steering wheel as they exit or get into the vehicle. This is typically caused by yanking the wheel while resting it against their body. It may also happen when an individual in the back seat is unable to stop it when they exit the car.

This is a quick fix that doesn't involve a trip to the mechanic or locksmith. First, make sure the gear shift is in either Park or Neutral. If it's not then gently pull or push the gear shifter until it moves to one of these positions. It's also important to press the brake or turn on the handbrake prior to attempting to turn the key.

If the wheel isn't locked, a quick look at the steering column will tell whether the key is engaged with the lock. This is usually marked by a tiny "Lock" label on the lower part of the ignition circle. You can easily disengage this by gently jiggling or pulling the key with moderate force. It is essential not to apply too much pressure since it could damage the key or damage a wafer inside the lock cylinder.

A spare key can also be used to unengage the lock. This could indicate that the original key is worn out and no capable of engaging the wafers in the lock cylinder. If this is the situation then a professional at Karl Chevrolet Webster City will be able to create a replacement key.

If the new key isn't engaging, a quick spray of penetrating oil can aid. Apply a small amount of oil around the ignition and inserted keyhole, then jiggle or tap it lightly until it begins to work. If this doesn't work, you will likely have to visit a specialist at your local auto dealership. They can provide you with a replacement key and also replace the ignition cylinder in case of need.

Check the Key

It could be that your key has been damaged if it will not turn in the ignition. Try getting rid of any foreign material that is on the key (lint or adhesive from packing tape, etc). You can also try rubbing rubbing alcohol on the key or Goo Gone to see if it aids.

It is possible that the lock pins inside aren't moving correctly when you insert the key. You can test the spare key by gently pulling it out of the ignition after having put it in. This should allow you to be able to feel and hear if internal lock pins move, as they ought to. If not, you could apply lubrication to the pins using powdered graphite. You can purchase graphite in small tubes that can be put directly into the keyhole. This should allow the pins to slide into position when you insert the key, and keep them from becoming stuck.

It is possible that your key has become damaged or worn out and isn't able to work with the pins in the ignition cylinder. This can cause the cylinder of ignition to not to turn, and prevent you from starting your vehicle. If this happens, you will need to bring your car to an auto locksmith ignition replacement locksmith or repair shop for repair.

If you are able to turn your vehicle with a spare key, and you've cleared the issue with the steering wheel or battery it could be because the ignition cylinder has worn out. It is possible to loosen the lock cylinder by using the blunt end of a screwdriver or the handle of the Hammer (not the head). Sometimes, a gentle tap on the cylinder will release it and allow you to turn the key of your car. If this does nothing, you'll need to have your lock cylinder changed by an expert mechanic.

Check the Ignition Socket

The ignition socket is the place where your key slides in and out when it is inserted. It is often filled with debris or is a result of regular wear and tear. You can spray some silicon lock lubricant in the ignition.

You can also use the small hammer, and tap gently on the inside of the ignition to loosen or reset pins that are out of alignment. Be cautious not to overdo it, or you could cause serious damage to the ignition switch.

It is crucial to confirm that your car's transmission is set to neutral or park before you attempt this. A lot of newer vehicles come with an option to lock the steering wheel when it is not in neutral or park. This could prevent the ignition key from turning.

If you've tried these steps and Car ignition locked your key still won't turn, it is possible that the ignition housing has to be replaced. Different vehicles have different methods of replacing the ignition cylinder. Therefore, it is essential to follow the correct steps.

Generally, this involves removal of the plastic cover which is over the steering column and ignition assembly. To remove it, you'll need adjust the tilt-wheel to its lowest position. Then unscrew any fasteners that are holding it in place.

After removing the cover you'll need to remove the old ignition cylinder from the steering column. It is then essential to check the new one you purchased with the old one to ensure that they are a perfect match. After this, you can install the new ignition cylinder the same manner as the old one.

It is possible that despite our best efforts, an ignition may become damaged and require to be replaced. If this happens, it's advised to contact a Tempe Locksmith for assistance. A locksmith can help you select the best replacement and install it correctly so that your vehicle can begin again.