• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace window pane Window Panes

A damaged or cracked window can be a nuisance. It could be a chance to upgrade your windows to energy efficient or insulated ones and enjoy advantages like improved comfort, increased resale values and reduced utility bills.

You can do it yourself for a only a fraction of the cost it would cost to employ an expert. It requires the right tools and an hour or two of your time.

Glass

If your single pane windows are old, deteriorating or broken replacing them with modern glass that is tempered or insulated can increase energy efficiency and reduce noise while maintaining the original character of older homes. The process of replacing the window pane is easy and can be accomplished by most homeowners who possess basic hand tools. You will also need an additional window pane, glazier's suggestions, pliers, and latex glaze putty. If needed you can use a heating gun to warm the old putty. Before beginning, wear gloves and safety goggles as working with broken glass may cause injuries.

Remove any broken glass pieces remaining. This can be done with a pair of pliers, however, a flathead screwdriver may work in the pinch. Then, use a wooden chisel or putty knife to remove the rest of the old putty from the frame and sash. Be careful to not damage the window sash. Be careful and slow. This is best done on a ladder, not the ground. Also, you should have someone on the ground to hold it steady.

Make sure that the window frame is ready to receive the new pane once you have removed the old putty. To allow for seasonal expansion or replace window Pane contraction and Replace Window pane contraction, subtract 1/8 inch from the measurements of the width and height. These measurements can be sent to an hardware or home centers store to get an item cut from glass stock to the proper size. You can also cut the glass yourself, if you have the appropriate tools.

After installing the new glass After installing the glass, apply caulking on the edges. This will make the glass weatherproof. Then, place a glazier's tip on the frame's opposite side to secure the pane in place. The points should not be tight enough to create friction between the frame and sash, but they should also not be loose.

Before applying the putty on the surface, you must knead it thoroughly until it becomes soft and free from lumps. Roll it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to the next and ensure that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that allow glass to be secured into the window frame without causing any damage to the fragile surface. Understanding how to use these tiny pieces of help is simple and could save you money on professional installation or the cost of new glass.

After the old putty as well as glazier's points are removed, thoroughly clean the frame using a utility knife to get rid of any remaining traces. Lightly sand the wood in the rabbet grooves if needed to smooth out rough areas. If you sand wood, protect it with painter's tape to avoid accidental damage.

Take the dimensions of the frame and note down precise measurements. Take these dimensions to a hardware store or a home center and request that the new pane cut smaller than the frame's opening. This will ensure a tight fit and leave room for expansion and contraction.

Place the new pane into the frame and press it into the frame using your hand. Make use of the point of the chisel, or the edge of the putty blade to smudge the glazier's points as shown in Figure 11. The glazier's points should be aligned with the top edge of the pane and the shoulders should be just beneath that lip.

Apply a thin layer glazing compound to the rabbet grooves and the edges of the new glass. This will seal and protect the edges. Let it dry completely and cure.

Once the glazing compound has dried, you're ready to install the new window sash. First, coat the wood with a heavy coat of linseed oil. This will stop the new putty from taking up the moisture and deteriorating and cracking over time. Apply the coat using a brush or the edge of your putty knife, then use the chisel or the back end from the putty knife to gently press the new sash and glazier's points into the grooves of the rabbet. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball that is thrown or an unintentional rock, or a fallen branch can cause a window to break or crack. Fortunately, windows replacement can be repaired by simply placing a new piece in the proper place. The glass is held into the position with a tiny metal clip, also known as a glazier’s point and putty. This compound is also called glazing compound. Remove the old pane and clean the area with the rag, a pull-type scraper, or a wood chisel. Wear gloves and safety glasses while working. If the window is glued to the frame, you'll have to employ a heat gun in order to soften the adhesive prior to cutting it loose.

If you are planning to replace window pane the original sash, take off the mold that holds the old pane. Sand the sash until it is flat and ready for new caulk. After the sash has been put back in place then, you can apply a silicone caulk to the glass. This will ensure that it won't get soiled or discolor over time.

Take out the glazing points in the rabbets. These are the grooves on the sash, where the glass is. If they're difficult to work out, you can try holding a hand tool like a heat gun to soften them before you do. If you're using a heat gun, be careful not to scratch the sash or its railings by holding the tool too close.

After the old points of glazing and putty have been removed make a bed for the new pane. Roll a rope of glazing compound between your hands, forming it into a 1/2-inch thick. Then, you can press it into the rabbets, where the glass will sit. The glass should rest against the putty on both sides. If you need to you want to tap your glass lightly into the rabbet with your thumb.

If the new pane has cracked, you can use a silicone caulk or glass glue that is based on solvents to fill in the crack before pressing it into the sash. If not, you'll have to putty over the crack to create an impervious seal to keep water out. Once the putty is dry clean the oily film off of the glass and allow it to dry completely before you paint. Paint after the putty has completely dried. It won't create a solid seal and may leak or discolor with time.

Paint

You may be concerned about replacing a broken pane of glass. In reality, replacing a single pane of glass doesn't have to be expensive if you do it on your own. Even double-paned windows can be replaced at a fraction of the cost it will cost a professional.

If you are working on a large window, ensure that it is securely fastened to the frame. By using the correct tools and techniques, you can make this task relatively easy and fast.

When you're ready to start taking off the old window pane by prying out the glazing points made of metal that are attached to it. They are basically tiny metal triangles which function as "nails" which hold the window in within the frame of wood. They are placed under a bead of glazing putty that is then cured to form a solid, molded wedge that secures the window in place and hides the points.

After taking off the old pane clean the frame and wood. Scrape off any paint that has been used and sand the rabbet grooves that the glazing points were placed. They should be sanded to bare wood to allow you to paint them the same color as the rest the frame. After sanding, apply a layer of flax oil on the wood that is not sanded down to prolong its life.

Then, take measurements of the dimensions of the window's opening. You'll need to take vertical and horizontal measurements of the entire opening and also the thickness of the old pane. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can take these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.