• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A cracked window pane is an inconvenience. It could be a chance to upgrade your windows to energy efficient or insulated ones to enjoy benefits like increased comfort, higher resale value and reduced utility costs.

It's a task you can do yourself for only a fraction of the cost of hiring a professional. It requires the right equipment and an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulate glass to improve energy efficiency, cut down on noise, and maintain the historic integrity of your old home. The procedure of replacing the window pane is simple and can be done by homeowners with basic hand tools. In addition to a replacement double glazing windows pane, the following components are required for the replacement handles for upvc windows process: latex glazing putty Glazier's points; pliers and a heat gun for warming the old putty if required. Before beginning, wear gloves and safety goggles as working with broken glass could cause injuries.

Take away any broken glass pieces that remain. This is best accomplished with pliers, however, a flathead screwdriver can also be used in the pinch. Then, use a wooden chisel or putty knife to remove the remaining old putty from the frame and sash. Be careful to not scratch the window sash. Take your time and work slowly. It is best to work on a stable ladder instead of the ground and have someone stand below the sash to help keep it in place.

Prepare the window frame to accommodate the new pane after you have removed the old glue. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Bring these measurements to a hardware store or home center and find a piece glass cut to size. You can cut the glass yourself if you have the appropriate tools.

After putting the new pane in place after installing the new pane, put a tiny amount of caulking along the edge to seal it against weather. Then, place a glazier's tip on the frame's opposite side to secure the pane in place. The points shouldn't be so tight that they create friction between the frame and the sash, but they should also not be loose.

Before applying the putty work it in a gentle manner until it is soft and free of lumps. Cut it into pencil-sized pieces. The first strip should be glued to the frame's corner. Work from one corner to another, making sure it is even and smooth.

Glazier's Points

The glazier's points are small triangular metal pieces that help secure the glass into the window frame without damaging the delicate surface. It's easy to understand how to use this nefarious tool, and you'll be able to save money on the expense of an installation by a professional.

After the old putty and glazier's points are removed Clean the frame thoroughly with a knife to eliminate any remaining traces. Lightly sand the frame in the rabbet grooves, if necessary, to smooth rough areas. If you sand wood, protect it with painter’s tape to protect it from damage caused by accidental sanding.

Write down the exact dimensions of the frame. These dimensions can be taken to the hardware or home center store and the new pane will be cut slightly smaller. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new window in the frame and push it into place firmly using your hand. Then, use the tip of your chisel or the back of the putty knife to make a tap on the glazier's points, as illustrated in Figure 11. When you're done, they should be level with the top edge of the pane and the raised shoulders of the points should be below the lip of the rabbet groove.

Apply a small amount of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow it to dry and cure completely.

After the glazing compound dries, you're ready to install the new window sash. First, coat the wood with a thick layer of linseed. This will keep the new putty from sucking in the moisture and drying out and cracking with time. Apply the coating using a brush this coat, or even the tip of the putty blade. Then use the chisel on the back of the tool or the back of the putty handle to gently hammer the new sash or glazier's tip into the rabbet grooves. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A hurled baseball or a rock that is errant or a falling branch can cause a window pane to crack or break. Most windows can be repaired easily by simply putting in a fresh piece. The glass is held in place by small clips made of metal called a glazier's point and putty, often called glazing compound. Before you install a new pane, first get rid of the old one and clean up the area using an abrasive and an abrasive scraper that is a pull type or an abrasive wood chisel. Wear protective glasses and gloves while working. You'll need a heat gun if the window is glued into the frame.

If you're planning to replace the original sash, take off the mold that holds the old pane. Then sand the sash to ensure it's level and ready to be re-caulked. After the sash has been re-installed then, apply a new silicone caulk to the glass to ensure that it will not leak or change color as time passes.

Take out the glazing points in the rabbets. These are the grooves on the sash, which is where the glass is. If they are hard to chisel, use an instrument such as a heating gun over them for a few minutes to soften them. If you're using a heat gun, be careful not to scratch the sash or its railings by using the tool too closely.

Once the old points of glazing and putty are removed, make a bed for the new pane. Roll a rope made of glazing compound between your fingers, and make it about 1/2 inch thick. Press it into the rabbets where the glass will be put. It's important that the glass rests against the putty in all places on each side So if you have to tap it, gently press the glass into the rabbet using your thumb.

If the new pane is cracked, you can cover it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If not, you'll have to putty over the crack to create an airtight seal and keep water out. Once the putty is dry remove the oily film off of the glass and let it dry completely before painting. Paint after the putty has completely dried. It won't form a good seal and could leak or discolor with time.

Paint

You may be concerned about replacing a broken pane of glass. But the truth is that replacing one glass pane does not have to break the bank if you do it yourself. Even a double-paned window can be replaced for a fraction of what it will cost for a professional.

If you are working with a large glass window, first make sure it is securely attached to the frame. With the right tools and replace Window pane techniques, you can complete this task easily and speedy.

When you are ready to begin taking down the old window pane. Take out the metal glazing points attached to it. These are small metal triangles that act as "nails", holding the window within the frame. They are buried beneath a bead or glazing glue which hardens into solid wedge which holds the wood frame in place and conceals the edges.

After you have removed the old pane removed Clean up the frame and wood. Scrape off any paint that has been used and sand down the rabbet grooves that the glazing points were placed. Sand them to bare wooden surfaces so you can paint the frames the same shade. After sanding, apply a coat of flax oil to the wood's surface to prolong its life.

Next, measure the size of the window opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening as well as the thickness. To get the exact size of the new pane, replace window pane subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these measurements to a hardware or home improvement store, and they will have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.