• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window handle Window Panes

A damaged window pane can be an issue. This can be an opportunity to upgrade your windows to energy efficient or insulated ones to enjoy advantages like improved comfort, increased resale value and reduced utility bills.

It's a task you can tackle yourself at less than the cost of hiring a professional. You'll only require the right tools and a few minutes of your time.

Glass

If your single pane windows are old damaged, cracked or deteriorating, replacing them with newer glass that is tempered or insulated can increase energy efficiency and decrease noise while maintaining the original character of older homes. The process of replacing the window pane is easy and can be completed by most homeowners who possess basic hand tools. You'll also require a replacement window pane, glazier's tips, pliers, and latex glaze putty. If needed you may use a heatgun to warm the old putty. Before beginning, wear gloves and safety glasses as working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. This can be done with the help of pliers though using a flathead screwdriver may work in a pinch. Then, use a wooden chisel or putty knife remove the remaining old putty around the frame and the sash. Be careful to not damage the window sash. Work slowly and carefully. This can be done best on an elevated ladder, not on the ground. Also, have someone on the ground to ensure it is held steady.

Make sure that the window frame is ready to accommodate the new pane when you have removed the old glue. Find the width and the height of the sash opening, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to a hardware store or home center and have a piece of stock glass cut to size. You can cut the glass yourself if you have the appropriate tools.

After putting in the new pane after installing the new pane, put a tiny amount of caulking along the edge to ensure it is weatherproof. Install a glazier's pointing on both sides of the frame. This will secure the pane. The points shouldn't be tight enough to cause friction between the frame and the sash, but they should also not be loose.

Before putting the putty on, knead it thoroughly until it is soft and free of lumps. Then make it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from one corner to the next to ensure it's even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal which help to secure glass into frames for windows without scratching or damaging the fragile surface. It's simple to learn how to use this hidden tool, and you'll save money on the expense of a professional installation.

After getting rid of the old putty glazier points as well as any remaining leftovers Clean the frame thoroughly using an utility knife. Lightly sand the wood in the rabbet grooves if needed to smooth rough areas. If you decide to sand the wood, be sure to protect it by using painter's tape to prevent accidental damage.

Write down the dimensions of the frame. Take these measurements to a hardware store or a home center, and have the new pane cut smaller than the frame's opening. This will ensure that the pane fits snugly and allows for expansion and contraction.

Place the new pane into the frame and press it down with your hands. Then, use the tip of your chisel, or the back of the putty knife to tap in the glazier's facets, as illustrated in Figure 11. The glazier's points should be aligned with the top edge of your pane, and the shoulders should be just below the lip.

Apply a thin layer of glazing compound on the rabbet grooves as well as the edges of the glass. This will protect and seal the edges. Allow it to dry and cure completely.

Install the new window sash when the glazing compound has dried. First, saturate the wood with a heavy coat of linseed oil. This will stop the new putty from soaking in the moisture and drying out and cracking over time. Apply this coat using a brush or the tip of your knife, then use the chisel, or the back end from the putty knife to gently press the new sash and glazier's point into the rabbet grooves. Repeat this procedure every 10 inches along the frame's perimeter.

Putty

A baseball thrown, a rock thrown in error or a branch falling can result in a cracked or cracked window pane. The majority of windows can be replaced easily by installing a new piece. The glass is held in the position with a tiny metal clip, called the glazier's point, and putty. This compound is also referred to as glazing compound. Before you install a new pane, first take out the old one and clean the area using a rag and the pull-type paint scraper or an abrasive wood chisel. Wear safety glasses and gloves while doing this work. You'll require a heat gun if the window is glued into the frame.

If you are planning to replace window pane your original sash, remove the molding that holds the old pane. Sand the sash until it's flat and ready for new caulk. Once the sash is re-installed then, apply a new caulk made of silicone around the glass to ensure it will not leak or change color over time.

Remove the glazing points from the rabbets. These are the grooves in the sash where the glass is located. If they're difficult to cut out, you can try holding a hand tool like a heat gun to soften them up first. If you're using a heat gun, be careful not to cause damage to the railings of the sash or the sash itself by using the tool too tightly.

After the old points of glazing and putty have been removed, prepare a bed for the new pane. Roll a rope of glazing compound between your fingers and make it about 1/2 inch thick. Press it into the rabbets, replace window Pane where the glass will be placed. The glass must rest against the putty on both sides. If necessary you want to tap your glass lightly into the rabbet using your thumb.

If the new pane is cracked, you can use a silicone caulk or glass glue based on solvents to fill in the crack prior to pressing it in the sash. If not, you'll have to putty over the crack to create an impervious seal to keep water out. After the putty has dried then clean the oily film off the glass using the help of a rag. Allow it to dry completely before painting. If you paint before the putty has completely dry, it won't form an effective seal and could be leaking or discoloring in time.

Paint

You might be worried about replacing a broken pane of glass. In reality, replacing a single pane glass doesn't need to be expensive when you do it on your own. Even double glazed window replacement-paned windows can be replaced for a fraction of what it costs a professional.

First, if you're working on a large-sized window, ensure that it is securely fixed to the frame. With the right tools and techniques to complete this task easily and quick.

When you are ready to start with the removal of the window pane. Pry out the glazing points made of metal that are attached to it. These are basically small metal triangles that function as "nails" that hold the window in in the wood frame. They are buried beneath a glaze putty or bead that sets to form an unbreakable wedge that holds the wood frame in place and conceals the edges.

After removing the old pane, clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points used to be. Sand them down to bare wooden surfaces so you can paint the frames with the same color. After sanding the wood then apply a layer of flax oil. This will help to extend its life.

The next step is to measure the dimensions of the window opening. You'll need to take vertical and horizontal measurements of the entire opening, as well as the thickness of the old pane. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasons of change. Take these measurements to the hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.